 | | Re: *** NQC ***
|
|
NQC is actually two things: a language to program the RCX and a compiler for that language. (at first I distinguished between the language: NQC, and the compiler: nqcc, but this was even more confusing) RcxCC is a great front-end for NQC. It (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Keep checking the math. I clocked the motor at 330 - 350 rpm. I used the rotation sensor driven directly by the motor. From analysis of the RCX firmware, the rotation sensor should be accurate to 1250 rpm, so I'm pretty confident of it being in the (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Virtual PC and Mindstorms
|
|
Robolab uses the same RCX as Mindstorms - I have one of each and they are identical (short of the number stamped on the side). Dave (...) reply to: dbaum at enteract dot com (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Dave- Where are you getting that 1250 rpm upper limit from? While I haven't counted exactly yet, I'm dropping only 20 counts out of every thousand at ~15,000 rpm. I had assumed this was mainly gear slop, since it only appears to occur while (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Using a Futaba 9ZAP radio with a built in optical tachometer and the two bladed LEGO prop I got 380 rpm for the gearhead motor and 4320 rpm for the older nongeared motor. Of course this was done with a battery box and brand new batteries so I am (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
My memory is a bit fuzzy here since it was a while back, but according to my notes... * sensors are sampled every 3ms * rotation sensor is a quadrature encoder with a 4:1 gearing in front of it (one rotation of the axle yields 16 "ticks"). * sensor (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Oh! Math mistake on my part... 16 instead of 4. Hmm... the ~15K was an off the top of the head estimate, which would go down to ~4K if divided by four again like it should be :) I'll have exact numbers some time today. Like I said, it is (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Ferret Bomb Disposal Unit
|
|
Anyone heard of this Robot? It supposed to be used in the NYC Bomb Squad. Know anywhere I can find a site or more info on it? Thanks. ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The (...) (27 years ago, 7-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | loading code
|
|
What is the first line to use for any IC program??? I'm using #include <stdio.h> and kepp getting compile errors. Tried variations but no luck. Thanks a lot! (27 years ago, 7-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: loading code
|
|
(...) Hi Bill ... Kill the #include ... IC doesn't use any header files. RTFM at: (URL) fun, - Nick - (27 years ago, 7-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) You could get close using the differential as an adder. The ratio of speeds above is about 11:1 (its 11.3:1, but lets keep things as integers). That is a prime number, and we know there aren't any lego gear options that give you an 11:1, so (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Assuming those numbers are correct (I've been too slack to actually look up the tooth counts), I'll give further clarification on my earlier post. I'm using a combination of three 40:8 combos, giving me an effective ratio of 125:1. The gearing (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: JVM port status
|
|
(...) Wow, looks like this is really off to a strong start! When/if you're ready for a dedicated mailing list/group, let me know if there's any way I can help out. The .robotics.rcx group is perfectly fine too, if you'd like to use that, although it (...) (27 years ago, 7-Jul-99, to lugnet.robotics.rcx)
|
| |
 | | Joystick Buttons
|
|
Has anyone figured out a way to utilize the buttons on the joystick? like maybe control another motor on top of the bot to turn an arm or something like that? -- Clay Aucoin (27 years ago, 7-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | encoders and analog ports
|
|
hi there i'm not yet receiving this list so could any replies please not leave out my direct email. my problem is thus. i've got 5 of the hb's analog ports used by ldr's. they all work fine and have done so as line detectors for 3 years now. i have (...) (27 years ago, 7-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | 8414 Mountain Rambler at K B Toy
|
|
I wasn't really sure which list to post this to, so I apologize in advance if you don't care about this... I just wanted to let the robotics crowd know about the availability of a pretty good technics set for relatively cheap dough. The 8414 (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 8414 Mountain Rambler at K B Toy
|
|
Chris, thanks for the notice, i am always looking for kits like this to integrate into my Mindstorms projects. Michael Aaron (...) (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 256 Colours
|
|
the problem with that is you have to reboot most of the time, so the solution is to get the freeware from microsoft (i think) called PowerTools 98 or actually 95, included is a piece of software called quickres that allows you to make changes to (...) (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | Re: 256 Colours
|
|
I believe the product you are looking for is PowerToys. I don't see a need to change the colors unless performance is greatly affected, so just ignore the message. Sorry if this was already said, I just don't want to read all of the posts. (27 years ago, 8-Jul-99, to lugnet.robotics)
|
| |
 | | ------( Welcome to lugnet.robotics.logo )------
|
|
Welcome to lugnet.robotics.logo, a LUGNET discussion group. CHARTER/PURPOSE: lugnet.robotics.logo (group): Discussion group for projects and educational activities involving LEGO® and the Logo programming language. lugnet.robotics (group and (...) (27 years ago, 8-Jul-99, to lugnet.robotics.logo)
|