 | | Re: Yellow Leds & Battery
|
|
(...) Sorry to have disturbed so many people but i finaly found the solution: my adapter war rated 1000 mA ..... and so it never give a voltage over 13 ... I got one supposed to be less powerfull (500 mA) and it just work fine!!! (...) What I meant (...) (29 years ago, 6-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Response to Fred's note..
|
|
This is a short response to Fred's message. There have indeed been problems in the past, this is one of the reasons why I am quiting as soon as I am out of debt. Any way, if you are worried about not getting stuff, you are protected if you use a CC. (...) (29 years ago, 6-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Handyboard assembly
|
|
We have assembled our fifth handyboard and have run into the following problem. (The other four boards went smoothly). The command dl pcode_hb.s19 downloads fine just as it did on the four other boards that we have built. However, when I power cycle (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Handyboard assembly
|
|
We have assembled our fifth handyboard and have run into the following problem. (The other four boards went smoothly). The command dl pcode_hb.s19 downloads fine just as it did on the four other boards that we have built. However, when I power cycle (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Serial Com. in IC
|
|
Hello folks, I have a group of students involved in an application where a PC needs to send commands to a handy board at certain instants and receive feedback from the handy board. The handy board is involved in motor control according to the (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Serial Com. in IC
|
|
yes, it is possible for an ic program to use the serial port. see randy's instructions at (URL) this question was answered and archived in Handy Board e-mail archive. It would be good if people try a quick search through there before posting to the (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard assembly
|
|
Ah, the classic "I built it and it doesn't work" story. Did you follow the incremental building instructions? I take it the answer is no. My suggestion is to pull all of the chips, and run through the series of incremental tests in the building (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard Kits
|
|
Dear Ram, I have not run into the exact problem which you describe, but I have some ideas which may be beneficial anyway. The first thing I would check is to make sure all the RAM pins are soldered properly. Since DL downloads the code without (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard assembly problem fixed
|
|
Dear Fred: No, we went through the assembly following your directions step by step. By the statement " Board OK", I meant that the tests upto the point of downloading pcode (second time with LCD in) tested OK. I did not want to bore the audience (...) (29 years ago, 7-Mar-96, to lugnet.robotics.handyboard)
|
| |
| | Vector 2X compass specs online
|
|
(...) I called Precision Navigation's fax-back service to get datasheets for this device. In case anyone else is interested, I put a copy of the datasheets I received on our web site at (URL) looks like a cool device, although we haven't tried it (...) (29 years ago, 8-Mar-96, to lugnet.robotics.handyboard)
|
