To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1161 (+10)
  E-mail Address
 
My e-mail is going psycho. just to make sure, my email address is:: ameba@mcleod.net -thanx (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
 
  Assembling the HandyBoard
 
Hello all: We got the handyboard assembly kit from Digital Micro Systems. We are putting it together now. Everything has gone well. Thanks, the instructions are really good. A couple of things have not worked quite right: 1. Couldn't find the 2.2M (...) (30 years ago, 25-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) You need that resistor to stabilize the crystal frequency. Try Radio Shack if it is missing from the kit. It doesn't have to be 1/8 watt, 1/4 or 1/2 watt is fine, just make sure it is 2.2 megaohm. (...) So far so good. (...) There is probably (...) (30 years ago, 26-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) I was getting similar behavior with my board. It wasn't clear to me that pins 2 and 3 in the serial cable from the PC to the interface board should be switched. Credit goes to Mike Ross for helping me figure this out. Once I switched these two (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Thanks, Fred
 
Fred, Thanks for giving us this great design. I appreciate it and I enjoyed building my Handy Board from a kit. I do have two corrections, though. No big deal, just typos. In the on-line assembly instructions, J15 is referred to as J14 at one point, (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) The whole issue of null (inverted) connections vs. straight-through is incredibly confusing, because you must take into account the gender of the connector (male pins or female pin sockets) in determining whether it is a null connection. Start (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Assembling the Handyboard
 
Hello all: We saw the recent message, same sub. We got our handyboard from Digital Micro a couple of days before the holidays. We had a great time building the boards. The kit is excellent. The instructions are great - even for novices like us. (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Hey, it works!
 
I can hardly contain my glee! After 3 weeks of fun-yet-obsessive, marriage-threatening, Xmas-be-damned behavior, I've got all four IC and OC interrupts going, receiving/processing/outputting 4 RC PWM signals. This is only a side-note for Handyboard (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  sending signals over power lines
 
hello. While this question doesn't pertain directly to the handyboard, I thought I would post it here since I am using the handyboard in my project. Some of you may have heard of this product: There are devices on the market (radio shack and a few (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  RE: sending signals over power lines
 
There is a good write up on this in one of Steve Ciarcia's columns in BYTE magazine some time in the early 80's. A quick stop at the periodicals desk of a technical library might help you here. --Chuck ---...--- From: Andrew S. (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR