 | | RE: Temperature sensor limits?
|
|
# From: tja@cpu.com # Sent: Thursday, April 15, 1999 04:58 PM # To: lego-robotics@crynwr.com # Subject: Temperature sensor limits? # ---...--- # Does anybody know what the measurement limits are for the temperature # sensor (particularly on the high (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Novice group
|
|
This one sounds like a good idea to me. Steve (...) (28 years ago, 15-Apr-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: Novice group
|
|
With the current amount of traffic going by these days, I'd say this is not necessary. Besides, it's refreshing to answer some basic questions once in a while. :-) I suspect the traffic will peak again in September to December, when LEGO introduces (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Temperature sensor limits?
|
|
(...) (Bitter) Experience tells me that at about 80 degrees Celsius*) the Lego plastic starts to get noticeably softer. At 90 to 100 degrees Celsius it will start to deform slowly without pressure. At this temperature most Lego will sustain (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | RE: SENSOR_READ doesn't return 0
|
|
(...) OOPS, that SHOULD read 0x0080 since the mode is a BYTE value. Overzealous urge to get content into the website is to blame. For the light sensor, I generally use the percent of scale mode. My website has a page on tricks with the light sensor (...) (28 years ago, 15-Apr-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: SENSOR_READ doesn't return 0
|
|
(...) John, Thanks a lot for this catch. Sounds a lot like the email I exchanged with Kekoa regarding power down mode and external stacks, but that's another story... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (...) (28 years ago, 15-Apr-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: Useful constants
|
|
(...) <snipped constant descriptions> John, These constants are indeed useful, but would make the resulting srec file pretty big. I have tried to make a TCL script to allow a sort of macro substitution. You can always load the constants after the (...) (28 years ago, 15-Apr-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: preventing IR tower shutdown
|
|
(...) Usually a capacitor lives across the power lines, and introducing a wire would be a good way of drianing the battery, burning the wire and possibly yourself!!! DON'T DO THIS... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | RE: Ir transmission
|
|
(...) Alas, I only used the firmware timers available as core RCX firmware calls. I can look through Kekoa's disassembly to see if there are higher resolution timers available ( I think the motor timers might be useful ) In general, NQC hooks in (...) (28 years ago, 15-Apr-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Novice group
|
|
(...) Ditto that. When I first picked up my mindstorms, I tried following .robotics for a while, but it was just too much effort sifting through the greek to get to the stuff I could understand. James (URL)Steve (...) (28 years ago, 15-Apr-99, to lugnet.admin.general, lugnet.robotics)
|