To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10716 (+10)
  Re: Desgning H-bridge
 
Hey Ericson, Check out the following sites for motor control information: (URL) under motor control Hope this helps, good luck! --kam (URL) Mon, 12 Apr 1999, MAR ERICSON wrote: -->Where can we get info in designing H-bridges from descreet (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Rangingproblems with Sharp GP2D02
 
Hi all I just finished rewriting the GP2D02 routines by Kent. Seems all to work just fine....except that I don't get readings below around 55. Even if I don't have anything in front of the sensor (dist. to wall more than 2m) I never get a reading of (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Desgning H-bridge
 
Another great source for h-bridge design if (URL) It gives details on how to build a PIC based motor controller, but more importantly, it has a great h-bridge schematic. Be sure to check it out. ---...--- Brian Schimpf schimpfy2@aol.com (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Rangingproblems with Sharp GP2D02
 
(...) I'm looking at the Sharp data sheet, and they have a chart that shows decimal distance measuring output vs distance to object in centimeters, and they indicate the minimum reading to be around decimal 59 to 64 depending on object reflectivity. (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Expansion Board Servo timing...
 
Drew- I have a Handy Board on a robot that runs three servos and the GP2D02 sensor, and I have the same nervous jitters problem. However, I do not run any processes on this application. I am using IC under v 3.2 of the software, so I could use (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Steering a robot
 
(...) On one of my robots I have a light sensor that I use the third motor to scan to the left and right. I use a single touch sensor and two cams such that it knows when it has reached either extreme. Using the Fwd(), Rev(), and Off() routines will (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Expansion Board Servo timing...
 
How sensitive are the exp bd servo routines to many processes running concurrently. My servo works fine in a stand alone test file but when I include it in my main code it gets the "nervous shakes", as if the timing pulse is fluctuating ( I don't (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: H-bridge
 
I am currently in search of H-bridges (DC motor drivers) I tried visiting wirz electronics but they aren't in business right now. does anyone know of any other places i can check out? =) thanx Chen (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Web site update
 
I have up dated my site with my Senior project that I built out of my lego mind stormes. Check it out (URL) on the senior project link Download Neoplanet at (URL) you check the web site first?: (URL) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Re: Steering a robot
 
(...) This is a good starting point for a gear system that uses one motor to drive both wheels, and another that adds and subtracts rotations from the wheels to produce turning. (URL) subject has been covered a lot in earlier messages, so it may be (...) (28 years ago, 12-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR