 | | Re: 4WD 4WS model w/limited slip diff. NOTE
|
|
PS. THe nice looking photos of the lego elements were cropped from originals found on the Technic Elements Registry: (URL) basically describe the key elements necessary to complete the model. (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) I think I'm in the process of writing up such a document. Combined with Fred's guide to programming the 6811 (which covers the miniboard nicely), hopefully this will fill the gap. (...) And using IC libraries works well, up until you have a (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Mid-South Robotics
|
|
If you live in the Memphis, TN...Jackson, TN...Little Rock, AR....Jackson, MS area, I am working to setup the Mid-South Amateur Robotics Society. A group that meets to show off Lego (and other) robotics projects and to swap parts and ideas. If you (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) You can have a copy of mine if you like. You can relocate it to any available digital ports with ease. It is set up for a single sensor, but you can easily add as many as you have ports for. (...) For people using the Handy Board in small (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | re: legOS for the helpless
|
|
(...) Sometimes more than once... :-) I just couldn't resist trying my hand at this, even though Dave beat me to it. Looks like they're both fairly similar. Mine will mail the s-record back to you if you like. I've tested it fairly extensively, but (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Power drain of the motors
|
|
Is there any way to measure the power drain of a running motor? The reason I ask is that I want to detect when the motor has stalled. I use nqc to program the brick. thanks -chris -- Did you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Power drain of the motors
|
|
(...) The CyberMaster can! ;-) Maybe there's some way you can connect one input to the motor output? Laurentino Martins [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | GCC/HC11 small patch
|
|
I contacted the original person who did the HC11 port to gcc (Otto Lind), and he pointed me to a patch for it. If you're using gcc-2.8.1 with the HC11 patches in it, you may want to try this: At line 502 of config/m6811/m6811.c, change from: { (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Increasing current output to motors on HandyBoard
|
|
Haven't actually tried it, but I was thinking of the same sort of thing. Use a FET for PWM and a DPDT relay for direction. practically speaking, if you only switched the relay when the FET was off, no power transition, etc.... If your 'bot moves (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Increasing current output to motors on HandyBoard
|
|
Howdy, My original suggestion was to use *solid state* relays. They don't have any contacts. I use them plugged right into my Rug Warrior board at the motor output ports (would work the same on my Handy Board, but I have it on a smaller base, and (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|