To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10646 (+10)
  Re: Increasing current output to motors on HandyBoard
 
Another solution to this which is easier but more expensive is to use the output of the motor driver chip to drive solid state relays. You need the relays that use 5 volts for control and that will switch DC. The relays I use have flyback diodes in (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  rpm of the Geared motor
 
Anyone know the rpm of the Geared motor. Thanks LINC (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
 
  Re: interactive C
 
I'll follow your suggest, thanks for the time you gave me. It has been very useful! Stefano ---...--- (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re : -> Interactive C
 
You help has been really useful, i'm going to visit thi slink immediately! Stefano Falconetti (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Even more remote controls
 
there are a few sites out there wif the required IR info.. I'll try and dig em up tomorrow morning.. I'm gonna get my self a blank GB cart, and the device to upload the data to the cart hopefully this comming friday.. -----Original Message----- (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  RE: rpm of the Geared motor
 
# From: ldsmith@pfc.forestry.ca # Sent: 09 April 1999 07:44 # To: lego-robotics@crynwr.com # Subject: rpm of the Geared motor # ---...--- # Anyone know the rpm of the Geared motor. # If you mean the one that comes with the RIS, it's 350. When I (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: loading s/w
 
(...) legOS has a software solution built-in - when you are ready to quit, hold down the on/off button and press the 'prog' button. Hope this helps! Cheers, Richard (28 years ago, 9-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: rpm of the Geared motor
 
(...) About 360 rpm, according to my measurements. The non-geared motor runs at about 4200 rpm. (...) Regards, Johannes. (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
 
  Re: Even more remote controls
 
(...) Since you can control the IR LED directly you should be able to get this all working in SW. You will need to modulate the IR with a 40Khz carrier. From there you then turn on and off the carrier to create the start, data and stop bits. This is (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: Increasing current output to motors on HandyBoard
 
I wonder if this would last since a relay is mechanical and I would assume that it would wear with all that "switching". Doe anyone have any experience with this? Thanks. ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR