To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10586 (+10)
  HB encoders question
 
Can the HB measure encoder pulses faster than 1 kHz? (this is the speed of the system interrupt) Assume we have an encoder that does 500 pulses per revolution. What happens when we exceed 2 revolutions per second? What happens if the encoder has two (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Re: gcc build instructions for linux
 
(...) Has anyone successfully built the above target using egcs-1.1.2? My attempt failed in libiberty: ... configure: error: installation or configuration problem: C compiler cannot create executables. make: *** [configure-target-libiberty] Error 1 (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  RE: Looking for Step-by-Step Instruction
 
Jonathan Knudsen is writing an O'Reilly book, details at (URL) . Asides from that, check the mindstorms website frequently... # -----Original Message----- # From: jeff@learningstar.com # Sent: 02 April 1999 19:19 # To: lego-robotics@crynwr.com # (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  RE: Walker
 
do you have to email html? It's rather irritating. # -----Original Message----- # From: Robot2n@aol.com # Sent: 03 April 1999 21:39 # To: lego-robotics@crynwr.com # Subject: Walker # # # ---...--- # ---...--- # [Unable to display image]Hi everyone, (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  Re: gcc build instructions for linux
 
I have. I got the same message. I assume it is part of the test suite. I just bit the bullet and did a "make install" anyway, and it works fine. I take it as saying that it cannot generate an executable for the host platform, which would be true, (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  New Robotics on my wepsite...
 
Reciently I aquired an web cam and I couldn't resist making an attempt at making a webcam robot. This is the 2nd generation of the webcam robot. 1st generation never nade it into final assembly. Next is adding the RCX after I get extensions for the (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  Re: gcc build instructions for linux
 
(...) I got the same message, and your reasoning about the content of the message sounds AOK by me. But then I did a make install, and that crudded out on me, with the message In file included from ../../../egcs-1.1.2/...com.c:198: (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: gcc build instructions for linux
 
(...) I did not have this problem. Sounds like Fortran. Did you 'make LANGUAGES="c c++"' or just 'make'? The latter makes the Fortran stuff, too. Remember that if you specify LANGUAGES when building, you should specify the same value when (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  Need info PLEASE
 
Hi, I have looked around on the mailing list and have not found anything that will answer this question.... I have an expansion board and want to use a 12v 2amp source for my motors. The hack listed in the FAQ is only for use on a handy board only, (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Hack for gearmotors sold by Acroname
 
Hi, The SOHO gear motors sold by Acroname have a high gear ratio and are too slow for what I needed (189:1 or something). The front gear cover is removable with two screws and one on the gears (there are 4 metal gears in addition to the small (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR