 | | GP2D02 and the expansion bd
|
|
I currently use the HB with the Polaroid 6500. I'm considering the expansion board and Barry Brouillette's GP2D02 routines for IR ranging. these routines interfere with the timing of the sonar.c routines or for that matter any other time critical (...) (28 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: square plates
|
|
(...) Scala has a 4x4 tile. Steve (28 years ago, 30-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Hand-Pump
|
|
(...) Well, I've actually built a compressor with one hand pump (with the spring removed). It was working, but I had to gear down the motor very much and the resulting compressor was very slow. You can see it employed in one of my robotic creatures (...) (28 years ago, 30-Mar-99, to lugnet.robotics)
|
| |
 | | cputs / argc,argv / snapshot
|
|
Hi, I implemented a cleaner cputs(). Should work with all compilers, also 20% smaller. I went ahead and implemented argc/argv parameter passing for execi as well. This prompted a bugfix for memcpy, which I did create. As I was at it, I also merged (...) (28 years ago, 30-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: cputs / argc,argv / snapshot
|
|
Oops. Did I say David? That's what you get for speaking on the phone and typing simultaneously. I meant Dan, of cause! (28 years ago, 30-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) Ken's comments made me look at it again: Gcc-2.6.3+HC11 now compiles fine for me on Solaris 2.5, but I know I had trouble compiling it on Red Hat Linux 5.2. I would go back and check that configuration one more time but for the fact that I now (...) (28 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: NQC tutorial available
|
|
Mark, In the section on "Display", you mention "Setwatch()" is available in V2.3. Any guess when this will be available? Thanks, -Phil (...) (28 years ago, 30-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) Another question: _which_ cross-assembler does it use? The one based on the ASXXXX cross-assembler (the so-called "Baldwin assembler") or another one? There are some bogosities that I know about with the ASXXXX cross-assembler/ linker. It's (...) (28 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) In the xasm/doc directory it says "ASxxxx Cross Assemblers, Version 1.1, June 1990. Submitted by Alan R. Baldwin, Kent State University". I guess that's your answer. Let me know a better route to follow for the assembler/linker please. (...) (...) (28 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) Okay, is it the one with my hacks, by any chance? You can tell if there's a file called lklibrary.c in the lnk-src directory. (...) "Requires more study". It needs more GCC toolchain mojo than I currently have. (...) That's true, but in a (...) (28 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|