| | for those who don't have enough 9V geared motors...
|
|
Hi all, .... the Party Packagers store at Orfus Rd & Caledonia in North York has a couple of the large 3571 ZNAP sets with motors for $10. Boxes are a little opened/damaged, so make sure you check the contents for those incredibly useful and (...) (22 years ago, 18-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
"Derek Raycraft" <derek.raycraft@sitraka.com> wrote in message news:3D87C15D.803080...aka.com... (...) You guys are so good at this! Iain (22 years ago, 18-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) Ok so I finish the base of the truck. (URL) is the older design. I still need to find the model for the 2 long half beam so I can model the new design. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) I'm not sure what was meant by saying flex tubing was used in design of the trucks discused in that thread. I did up a diagram of my truck, but I can't post it at the moment. Hopefully later tonight or tomorrow. Basicly you pop the wheels out (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
"Larry Pieniazek" <lpieniazek@mercator.com> wrote in message news:H2L3L5.Hsu@lugnet.com... (...) used (...) flex tubing with this? Iain (STILL confused about the trucks) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | New Stuff at Walmart and Winners
|
|
Just found 4105 for $14.99 at Walmart today. This is the 500 piece Creator bucket. A little expensive, but a nice assortment. They also have the green and orange Duplo buckets in too. Also found a number of clocks for $29.99 there too-there's a (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) hehe, what could you be referring too? :-) Actually the point has become moot. As it turns out the interference of other parts has made it unnessisary to cut flex tubing after all. The pneumatic T-connector will do just fine. Its nice to know (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) Yes I think this is the part Iain is wondering about. (...) Yes I'm using a similar design, to what they are talking about in this thread, for my trucks. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) Yes this is one of the parts I'm talking about, but I don't think it's the one Iain is wondering about. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|
|
| | Re: Is it wrong to cut up flex tubing?
|
|
(...) I'm tremendously glad to see the consensus on this one! I've taken my knife to many a flex tube, usually with nagging doubts as to the purity of that act. The ultra-purists in NELUG seem comfortable with it, but it's nice to know that others (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
|