 | | Re: Demag cc12600 Crawler Crane
|
|
(...) the lateral bracing is really important, do as much as you can to brace it, it is one of the few problems with my boom, the mast will shift causing the boom to lean, then it falls, and youll probobly have to fix more than just the boom. and (...) (21 years ago, 31-Mar-03, to lugnet.technic, lugnet.modelteam)
|
| |
| | Re: Demag cc12600 Crawler Crane
|
|
(...) I saw it yesterday, it looks promising. (...) bracing's overlap forming a cross while on prototype cranes there's just one bracing forming a triangle. Steve (21 years ago, 31-Mar-03, to lugnet.technic, lugnet.modelteam)
|
| |
| | Demag cc12600 Crawler Crane
|
|
I was just surfin' through Brickshelf and came across Chris Davis' Demag CC12600 model: (URL) rederings of CC12600) (URL) construction- turntable and part of crawler base) Anyone else seen this? Looks like a monster! My only advice would be to (...) (21 years ago, 31-Mar-03, to lugnet.technic, lugnet.modelteam)
|
| |
| | Re: Cool Stuff on Brickshelf
|
|
(...) One of the best I've seen (and your Chevelle is amazing too, right down to the under side detail with the flex tubing for the exhaust and the engine transmission look). This beats the new 2003 4004 truck ALL to hell (we don't need no stinkin' (...) (21 years ago, 29-Mar-03, to lugnet.modelteam)
|
| |
| | Re: red baron with engine
|
|
I don't know the construction of the baron at all since I don't have one (yet!), but would it be possible to do it with the motor further back and a flex axle? Duq "Lars Gjerløw Jørgensen" <lgjPURGE@jyde.dk> wrote in message (...) (21 years ago, 28-Mar-03, to lugnet.modelteam)
|
| |
| | Re: red baron with engine
|
|
(...) The micro motors have a tendency to stall and if they do the internal gears often bind. If you're lucky it can be fixed by forcing the shaft around. (...) So it can be replaced with some smaller parts and a motor :) (...) Detsamma! Best (...) (21 years ago, 28-Mar-03, to lugnet.modelteam)
|
| |
| | Re: red baron with engine
|
|
Tobbe Arnesson's utterance expressed in news:HCG5GJ.1syp@lugnet.com: (...) hehe (...) My micro motor had a heart-attack during micro-twirp-development, so I'm awaiting a replacement from TLC. (...) That is by far the most spaceconsuming solution on (...) (21 years ago, 28-Mar-03, to lugnet.modelteam)
|
| |
| | Re: red baron with engine
|
|
(...) Perhaps you can gear the micromotor so it makes the prop. spin fast? The prop. moves pretty easy so it could be possible. Or if you redesign the whole internal front you might be able to put the geared motor in there? The big grey studs on (...) (21 years ago, 28-Mar-03, to lugnet.modelteam)
|
| |
| | Re: new 2003 sets
|
|
(...) No one even mentioned what looks like a mini millenium falcon there. I CAN'T wait for the AT-AT and that backhoe 8455!!! Even that truck looks pretty good, and I typically don't like the "specialty" parts that that set has for all the smooth (...) (21 years ago, 28-Mar-03, to lugnet.technic, lugnet.modelteam)
|
| |
| | red baron with engine
|
|
Tried to mod the red baron (10024) with an engine. Has anyone succeeded in doing this internally? I think it looks a bit odd this way: (URL) moderation: (URL) one could do it with a micromotor - but that will not look at all like a real plane-engine (...) (21 years ago, 27-Mar-03, to lugnet.modelteam)
|
