 | | Green plate sizes? —Bruce Schlickbernd
|
| | | Do green plates come in the following sizes: 12x4 12x6 12x8 I suppose I can always cut up the big baseplates to serve my purpose, but bfore I do, I thought I'd check. (24 years ago, 23-Oct-00, to lugnet.general)
|
| | | |
| | | | | Re: Green plate sizes? —Kevin Zwicker
|
| | | | | (...) There is one of each in 3134 McDonald's Restaurant. (...) I have never seen one. (...) Nooo...ooo!!!! ;-) Kev Z #142 (24 years ago, 23-Oct-00, to lugnet.general)
|
| | | | | |
| | | | | | | Re: Green plate sizes? —Erik Olson
|
| | | | | | Hold on--cutting up flimsy baseplates doesn't send you to the Dark Side. They make them flimsy on purpose so you can cut out just what you need. Right? I only do it with the huge gray ones to make custom floors inside my buildings. (Nobody remember (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Kevin Zwicker
|
| | | | | | (...) buildings. (...) I must admit that I have cut a few straight road plates in half. How have you done it? I used an exacto knife, but had trouble cutting in a straight line despite using a ruler. Also, Do you cut from the top side or the bottom? (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Erik Olson
|
| | | | | | | Ooh. I have to admit I'm not very good at those cuts. Exacto would take forever and wear out your blade I think. I just use scissors. Let us know if you hit on any other sharp solutions. One tip: put a brick on the plate and try to cut at a slant (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | | |
| | | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Lester Witter
|
| | | | | | | | (...) forever (...) on (...) would (...) You might try taping the base plate to a piece of plywood (use double stick tape) and cutting it in a bandsaw. This would allow you to use a fence to get a strait cut and a bandsaw produces a very small kerf. (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | | | |
| | | | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Tom Stangl
|
| | | | | | | | Exacto knives work just fine with baseplates, just get a metal ruler, hold it down firmly on the bottom of the baseplate, and VERY lightly slide the knife across the first time to set the cut line. Then you can bear down afterwards and cut through (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Will Hess
|
| | | | | | (...) you (...) line (...) Patience. Clamp the plate and ruler together and make many (MANY!) light cuts along the surface of the plate (1). This takes a while but it works! Will Lego Beach Department of Emergency Services www.crosswinds.net/~hokie (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Frank Filz
|
| | | | | | (...) I haven't tried, but you should be able to get a nice clean edge by scoring with a knife (one pass) and then snapping. If done right, you don't break either piece. You also shouldn't feel bad about cutting base plates. In just a brief look at (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —John Radtke
|
| | | | | | | (...) Has anyone tried using a big paper cutter? You might need to clamp it down somehow to prevent it from pulling to the side but it may work pretty well. John member #388 (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | | |
| | | | | | | | Re: Cutting baseplates (Was: Green plate sizes?) —Steve Bliss
|
| | | | | | (...) For some reason (ie, "I heard somewhere, at sometime"), I was thinking that baseplates were formed by more of a continuous sheet-feed mechanism. Some kind of vacuum-forming, but with higher precision. Steve (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | Re: Green plate sizes? —Peter White
|
| | | | | (...) 7128 Speeder Bikes has one 4 x 10 plate (but it's the lighter green shade). 7124 Flash Speeder has some 4 x 4 plates (normal green). pw (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | |
| | | | | | | Re: Green plate sizes? —Erik Olson
|
| | | | | | (...) 3438 McDonald's has your 12x4 and your 12x6. It's $10 from Shop At Home. 7115 Gungan Patrol has 2 4x4, and somewhere I got a 6x6. 7144 Slave I has a 2x10. Mos Espa only has dumb triangular 3x3 and car-roof 4x4. (Well, I did need a car roof.) (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | | |
| | | | | Re: Green plate sizes? —Damian Garcia
|
| | | | | "Bruce Schlickbernd" <corsair@schlickbernd.org> wrote in message news:G2wInG.F99@lugnet.com... (...) 6024 comes with 1 of these. (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | | |
| | | | | Re: Green plate sizes? —Selçuk Göre
|
| | | | (...) I've seen them but can not recall from which sets. They are standard plates bye the way, not base plates. (...) There is no nx8 plates where n>6..:-) But there is a standard base plate size as 16x8. (...) It's your piece of course, but (...) (24 years ago, 24-Oct-00, to lugnet.general)
|
| | | | |
