|
| | Re: LDraw coordinate system driving me crazy
|
| (...) I agree with Tim. It looks fine to me. If there were any mirroring going on, then either the orange and red would be swapped on the unwrapped box, or the green and grey would be swapped. The picture in LDView has a rotated camera angle (...) (18 years ago, 19-Nov-06, to lugnet.cad.dev, FTX)
| |
| ldraw (score: 0.452) |
|
| | Re: LDraw coordinate system driving me crazy
|
| Hi, Here's my box test model in SketchUp. (The above model is the same model unfolded.) (URL) When I export this model to a .dat and open it in LDView, the green side is the top-view, blue is the front view (as expected), and I would expect the (...) (18 years ago, 19-Nov-06, to lugnet.cad.dev, FTX)
| |
| ldraw (score: 0.452) |
|
| | Re: LDraw coordinate system driving me crazy
|
| (...) I've always understood it is: X positive is right X negative is left Y Positive is bottom Y Negative is top z Positive is back z negative is front In fact you can show this by adding a brick in MLCad and moving it around, watching how the X, Y (...) (18 years ago, 19-Nov-06, to lugnet.cad.dev)
| |
| ldraw (score: 0.452) |
|
| | Re: LDraw coordinate system driving me crazy
|
| (...) That looks like a correct mapping to me. Unless I'm mistaken the red and orange are on the same sides in both pictures. The unwrapped boxes are definitely identical and unless you've moved them in one or the other the whole thing is right. Tim (18 years ago, 19-Nov-06, to lugnet.cad.dev, FTX)
| |
| ldraw (score: 0.452) |
|
|
| ldraw (score: 0.452) |
|
|
| ldraw (score: 0.452) |
|
| | LSynth electric cable cross section oriention problem
|
| Hi, I've got a reworked version of LSynth with a major problem... I cannot figure out how to control the twist of the cross section. I use bezier curve to created the nicely curved set of points, and compress it by tossing out points until the angle (...) (18 years ago, 24-Nov-06, to lugnet.cad.dev)
| |
| ldraw (score: 0.451) |
|
|
| ldraw (score: 0.450) |
|
|
| ldraw (score: 0.450) |
|
|
| ldraw (score: 0.449) |
|
|
| ldraw (score: 0.449) |
|
|
| ldraw (score: 0.449) |
|
| | Re: Non-CA parts rewrite
|
| (...) We just got an affirmation from Bernd Munding, author of 3839a.dat - Plate 1 x 2 with Handles Type 1. Like John Jensen's Technic Bucket 10 x 8 also this part has been rewritten (URL) for the record: if you wanna contact Bernd please use his (...) (18 years ago, 1-Nov-06, to lugnet.cad.dev.org.ldraw)
| |
| ldraw (score: 0.449) |
|
| | Re: Non-CA parts rewrite
|
| (...) We've got an affirmation from John Jensen for 2951.dat - Technic Bucket 10 x 8 but it looks like Guy Vivan was faster! The rewrite is already on the PT: (URL) and just needs to certified by the admins. Which action should be taken?? w. (18 years ago, 30-Oct-06, to lugnet.cad.dev.org.ldraw)
| |
| ldraw (score: 0.448) |
|
|
| ldraw (score: 0.448) |
|
|
| ldraw (score: 0.448) |
|
|
| ldraw (score: 0.448) |
|
|
| ldraw (score: 0.447) |
|
|
| ldraw (score: 0.445) |
|
|
| ldraw (score: 0.445) |