 | | Re: Inline POV-Ray code?
|
|
(...) Yes, there are plans for this. My current issue is with the syntax being used. I'd rather use general 0 IF ... 0 ELSE ... 0 ENDIF meta-statements, rather than the 0 L3P meta-statements. (...) It seems like LGEO is pretty static now. Lutz is (...) (23 years ago, 20-Feb-02, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | Re: Inline POV-Ray code?
|
|
"Travis Cobbs" <tcobbs@REMOVE.halibut.com> wrote in message news:GrstMI.BB7@lugnet.com... (...) Brings me to a question about the minifig head. I had a high-res printout of Cale Leiphart's The Fight scene made for BricksWest, and there were some (...) (23 years ago, 20-Feb-01, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | New LDView screen saver mode
|
|
I don't include instructions in the release, but LDView 1.9.2 can now be used as a screen saver. This is still in the verification stage, and as such may lock/crash/reboot your computer, etc. (Note that it does none of these things on my computer.) (...) (23 years ago, 20-Feb-02, to lugnet.cad.dev)
|
| |
| | *** LDView Version 1.9.2 Released ***
|
|
LDView version 1.9.2 is now available, in both source and binary forms. You can download either from: (URL) of the highlights of version 1.9.2 include: Option to texture map LEGO logo onto studs. Wireframe Cutaway Faster lighting (on some cards (...) (23 years ago, 20-Feb-02, to lugnet.announce, lugnet.cad, lugnet.cad.dev)
|
| |
| | Re: Inline POV-Ray code?
|
|
(...) Yes, that's the info I'm looking for. Thanks, Travis (and Vincent, too). Related question (for the parts officials, I suppose): Are there any plans (even tentative) to move towards adding this sort of stuff to official parts? Or is the current (...) (23 years ago, 19-Feb-02, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | Re: Inline POV-Ray code?
|
|
(...) I don't know if any official parts do it, but it is possible. Based on an earlier lugnet.cad.ray message, you do this: 0 L3P IFNOTPOV (regular ldraw code goes here) 0 L3P ELSEPOV 0 (POV-Ray code goes here, commented-out) 0 L3P ENDPOV You can (...) (23 years ago, 19-Feb-02, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | Re: Inline POV-Ray code?
|
|
Tony Hafner <hafhead@PANTSplanetquake.com> wrote in message news:GrsoEF.Ips@lugnet.com... (...) any. (...) Read Steve Bliss' reply to my message titled "How to add own parts to LGEO?". He describes how to include POV-Ray code in .DAT files that can (...) (23 years ago, 19-Feb-02, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | Re: File Check utility (was: Case of part filenames?)
|
|
(...) OK, it's done. It will probably be a problem going forward, until I can clean up the code and combine it into one source. Anyone ever played with lex and perl? That would probably be a better way of doing this - the current code is pretty (...) (23 years ago, 19-Feb-02, to lugnet.cad.dev)
|
| |
| | Inline POV-Ray code?
|
|
I seem to recall that some curved parts have separate definitions in the parts file itself for POV-Ray to render them better. But I can't find any. Is this actually possible? Do such parts exist? Is there a "better" way (ie through L3P) to get (...) (23 years ago, 19-Feb-02, to lugnet.cad.dev, lugnet.cad.ray)
|
| |
| | Re: File Check utility (was: Case of part filenames?)
|
|
(...) Yep, I will do that. I think it should be pretty straightforward. Not quite as straightforward as it would be if they actually ran off the same source code, but close... Steve (23 years ago, 19-Feb-02, to lugnet.cad.dev)
|
