 | | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) There's one hole through the stud and the base where it is placed. Leonardo (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) True. As the best way to keep everyone at least somewhat happy. (...) I don't want to over-use 3-digit numbers. Only where necessary and unavoidable. For instance; The complete yellow dinghy does have the correct number. So we can make a (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) We could go that route, just have the two halves and no shortcut. The important thing is this would still be an accurate use of the numbers, but without carring it to the logical extreme and having the complete part. (...) True. Note that in (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Technic Axles - go rounded?
|
|
(...) Won't changing the length change the ease of modeling? Currently, you can line parts up (such as connectors or bushings) to the end of the axle because when lined up corectly, they share a common plane. If you make the axles shorter, this (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) Holes through the stud, or holes through the ball? Steve (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) hehe.. i can always count on you to be a pain, steve... :) every morning i come in here and check this thread and i can see everyone's point with equal value... i started in on this convo from the standpoint of "2 #16 parts, then aggregate (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Technic Axles - go rounded?
|
|
(...) The axles are shorter than bricks. Comparing the 2L axle to a 2x brick, the axle comes up about 1.5 LDU short. I haven't checked the other axles, for now I'm guessing they are also 1.5LDU short. (...) I posted one a few days ago. It was the (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) I'm not confusing them. But I can't speak for other people. Once we've got part-files created, we'll have firmer ground to talk from. Steve (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) I wonder -- are there color-specific part numbers for the dinghy, because it is a compound element? So if we publish two sub-files, and no shortcut, we skip the whole issue. But not publishing a shortcut seems really lame. The "part" is final (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) Just to be a pain: there are existing 'glued-together' parts in LDraw with sub-files for each component part and a main short-cut file for the whole thing. Two that spring to mind are the 2x2x11 pillar and the classic 2x4 plate hinge. (...) (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
