To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.devOpen lugnet.cad.dev in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / Development / 5698
  Re: License - again
 
"Frank Filz" <ffilz@mindspring.com> wrote in message news:3A36D1B3.4287@m...ing.com... (...) This is the perfect example of the line we should draw with regard to converters. There are two main tools which convert an LDraw model to POV-Ray: L2P and (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
 
  RE: License - again
 
(...) Actually, L2P uses the LGEO library written by Lutz Uhlman. Lutz also wrote L2P and all the textures that LGEO uses. AFAIK, Anton Raves has no connection with L2P at all. It's difficult to use Anton's parts because not only the coordinate (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
"Bram Lambrecht" <bram@cwru.edu> wrote in message news:MABBIBJJFOJIOHD...wru.edu... (...) part in (...) The (...) relied (...) wrote (...) not (...) different. (...) LDraw (...) directly. (...) Thanks for the correction and lists. John Van (24 years ago, 13-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
In lugnet.cad.dev, Bram Lambrecht writes: [snip] (...) Filip Spacek did the conversion. (...) It would be great if when/if MLCad started allowing plugins, someone wrote a converter to POV which worked directly in MLCad. This would make life a bit (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev, lugnet.cad.mlcad)
 
  Re: License - again
 
(...) Yes, definitely. Nicely said. Steve (24 years ago, 13-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
(...) Actually LeoCAD is somewhere between L2P and L3P. When converting a part to POV it searches first in LGEO then if the part does not exist in LGEO (or LGEO is not installed), it creates the part from the LeoCAD library, just like L3P. It's a (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
(...) It may be worth to note here that the binary format for LeoCAD falls into the former category. And as Leonardo Zide has said, James Jessiman did allow him to redistribute the transformed parts library independent from the main LDraw (...) (24 years ago, 14-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
"Fredrik Glöckner" <fredrik.glockner@bio.uio.no> wrote in message news:m3vgsm23c1.fsf@...ldomain... (...) It certainly should be given weight in any discussion of LeoCAD, and might help set precedent. Was giving credit to LDraw and part authors on (...) (24 years ago, 15-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
(...) My only source of information about this is: (URL) haven't found any of the other 100 places where Leonardo Zide has talked about this. Fredrik (24 years ago, 16-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
(...) James didn't want me to distribute the library in the original format, because he wanted to have the original library available only from his page but after I told him that I was using a modified format he said there were no problems. If you (...) (24 years ago, 16-Dec-00, to lugnet.cad.dev)
 
  Re: License - again
 
(...) Tim will have to correct us, but I believe that James's family has given Tim permission to continue publishing James's work. This is probably something which should be properly ironed out with the Jessiman's. They will have to decide to what (...) (24 years ago, 19-Dec-00, to lugnet.cad.dev)

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR