 | | Reference Site Inconsistencies
|
|
I was cross-checking some information between LDraw/Partsref, Lutz Uhlmann's Parts Reference, and James Jessiman's Unofficial LEGO Parts Listing. I was specifically looking at the parts with number less than 1000[1], because I need to get a better (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: getting started making pieces
|
|
(...) Welcome - new part authors are always welcome. The following is my preferred method of doing decorated parts as is a good grounding if you go on to author complete parts - others have had some success with BMP2DAT for decorated parts. 1. (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | getting started making pieces
|
|
A naive question perhaps, but I can't find the answer anywhere... I want to try my hand at making parts for ldraw, specifically I want to make minifig faces and torsos that haven't been done yet. What program(s) do you wizard-types use to make the (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: Update 9906
|
|
(...) for (...) sample (...) Yes you're right, and I've done enough torsos that I should not have made such an error. Chris (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: Update 9906
|
|
(...) You're right, I gave that suggestion some time ago. The subpart only had the back surface when it was using the old number. Leonardo (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: part 2951, some questions [DAT]
|
|
(...) I will centre between the lower pegholes then. (...) Goood:) (...) correction: I will not put the measurements up, as they are changing as I get along. Look below for more on this. (...) As of now, it looks like the worst part is figuring out (...) (25 years ago, 5-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: Update 9906
|
|
(...) I got the fixes. Thanks for the rapid turn-around, Chris! About 973s01 - I don't remember if this subfile ever had a back surface. The name does clearly state that there's no back: "~Subpart Minifig Torso without Front or Back". IIRC, the back (...) (25 years ago, 5-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: Update 9906
|
|
(...) Looks like both John and I mistakenly assumed that s\973s01.dat is the torso missing the front surface - in fact it is missing the back as well to cater for those rare torsos with decoration on the back. I sent a corrected version of 973p34 to (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: part 2951, some questions
|
|
(...) I'd say that's a good place to put the origin. On the other hand, the user is fairly likeliy to tilt the bucket off an axle in either the upper or the lower pegholes, so centering the part in the centre of either the upper or lower pegholes (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev)
|
| |
| | Update 9906 [DAT]
|
|
Hi, I was looking at the new parts and discovered that 2 torsos (973p34 and 973p101) are missing some faces from the back. It's not a big deal but it should be fixed on the next update. Also, 4522 (Minifig Tool Mallet) has some blue faces: 1 1 0 0 (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev)
|
