 | | Re: DAT voting page up
|
|
(...) i have fixed that and send the fix to terry. (...) i will fix this asap (...) i will not fix those (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
well... my raised baseplate is that accurate and is finished. (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
Sproaticus wrote in message ... (...) My vote would be to use the part number that people can see with out takeing apart the boat, i.e. the 30086 number. The 30087 number is only of value if you take the boat apart. Somthing I feel very few people (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
(...) need (...) You should measure with a ruler or with lego parts (or for detailed parts people have resorted to calipers). With a plate and a brick, you can make pretty accurate measurements based on wall thickness (4 ldu), plate thickness (8 (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
Terry K wrote in message <36d5fd53.5480877@lu...et.com>... (...) seemingly (...) number (...) both (...) I thought you had to break the two halves apart to get at the 30087 number. Do you have to break it apart? If so can you use them afterward? If (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
jonathan wilson wrote in message ... (...) go (...) need (...) Its precise enough for me. Since we already know that LDraw itself is not accurate, but it is precise. Roy (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
jonathan wilson wrote in message ... (...) done (...) You know, I've never looked at the bottom since you usually can't do anything with the bottom of a baseplate. Matter of fact I don't think I've ever looked at any of the real ones I have other (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) time (...) Some things to think about: It would be irritating in Ldraw to have to page through lists that look like this: xxxxx.dat Blah blah blah X blah Tr. Yellow-Green yyyyy.dat Blah blah blah X blah Gold zzzzz.dat Blah blah blah X blah (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: DAT voting page up
|
|
wht the raised baseplate: for example the "walls" of the small 4 stud area go up 3 bricks and accross 1/2 a stud area. is this accurate enough or do you need to measute with a ruler? (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) Hmmm.. well, we *could* have them all... use 30086 and 30087 as the two parts of the dinghy... then have part 4106548 simply reference the two "subparts" and have this "element model" hard-coded in yellow... anyone wanting to use a different (...) (26 years ago, 26-Feb-99, to lugnet.cad.dev)
|
