 | | Centering (was: I need help with the new tread links) —Dave Schuler
|
| | | (...) Actually, you've mentioned off-handedly something that's been bugging me for a long time; how do you "set" the center of rotation? As with a lot of my questions, I'm afraid the answer might be embarrassingly simple, but I haven't been able to (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | |
| | | | | Re: Centering (was: I need help with the new tread links) —Larry Pieniazek
|
| | | | | That was a trick answer. I don't know how and I am hoping someone will say how. I think MLCad takes the center of the grouping bounding rectangle. It certainly doesn't seem to be based on the origin. I had a submodel that I made sure had its 0,0,0 (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | | |
| | | | | Re: Centering (was: I need help with the new tread links) —Fredrik Glöckner
|
| | | | (...) In LEdit you can set the rotation centre with the keystroke "/ T C". I don't know about other LEGO CAD packages, but I think they should follow the LEdit standard when it comes to keystrokes. Fredrik (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Dave Schuler
|
| | | | (...) That works fine for me, because for now I use LEdit almost exclusively. I'm a little familiar with the "/T C" function; does this set the "center" to the center of the piece? How about when using subassemblies while drafting larger (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Bram Lambrecht
|
| | | | | (...) / T C sets the center of rotation to the position of the blinking cursor and leaves it there until you change the center of rotation again. When you start the program, the center is at 0,0,0 --Bram Bram Lambrecht / o o \ BramL@juno.com (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Fredrik Glöckner
|
| | | | (...) Yes to both questions. If you are unsure about the centre of the part you are currently working on, you can temporarily switch to a different part, move it around, set the centre, and LEdit will remember this 'till the next time you reset the (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Dave Schuler
|
| | | | *snip* (...) *snip* Thanks for the elucidation! One last question: how do you set the center of a piece permanently, as in a new DAT file? I notice, for example, that doors rotate on the anchoring studs, rather than on the center of "mass" of the (...) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Bram Lambrecht
|
| | | | (...) Move all the pieces so that the center of rotation is at 0,0,0. For some tips on how to do this, read the advanced lessons at: (URL) Lambrecht / o o \ BramL@juno.com ---...---oooo-----(_...o---...--- WWW: (URL) (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
| | | | | | Re: Centering (was: I need help with the new tread links) —Dave Schuler
|
| | | | (...) Thanks for your patient answer. Dave! (25 years ago, 26-Nov-99, to lugnet.cad.dev)
|
| | | | |
