To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.devOpen lugnet.cad.dev in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / Development / 1692 (-10)
  Re: Torso number was Forestman Torso was Voting Page
 
Chris Dee <chris_w_dee@hotmail.com> wrote in message news:FBoGA9.MAy@lugnet.com... (...) Except that some pXX numbers are consistent across a theme. All the M:Tron patterned parts are XXXXp68, for example. This makes them easier to remember. -John (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: Torso number was Forestman Torso was Voting Page
 
(...) that (...) and (...) numbers (...) which (...) problem (...) a (...) If we must make this move, let's use up the gaps - I suggest 974 - as close to the arms as the hip piece is to the legs - but I guess it makes little difference. This would (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Suggestion for LDraw FAQ
 
[crossposted to lugnet.faq and lugnet.cad.dev, followup-to set to lugnet.faq] Looking at the LDraw FAQ, it looks like a new level of organization is needed, above the current levels. More precisely, a large number of the topics should be grouped (...) (25 years ago, 13-May-99, to lugnet.faq, lugnet.cad.dev)
 
  Re: Torso number was Forestman Torso was Voting Page
 
(...) So waittaminut. I read you writing that 9326 *was* a number for the composite torso-with-arms-and-hands, but is not any longer used for that purpose. The 9xxx numbers were an earlier composite range. New parts are made with 5-digit numbers. So (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: Working on Part 30384
 
(...) There is still a 'primitives committee' which discusses new primitives before they are released. We decided awhile ago to not introduce new primitive files, until/unless they were actually used in a file. Which is why the ldraw/p/ directory (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: 99-03 Voting: Quick Comments
 
(...) Coz they didn't? The nut is a unique part, as far as I can tell. It is round, and ribbed on the outside (ribs parallel to the axle), and I've never seen a part that could be machined down to make it. (well, not easily, you could probably (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Torso number was Forestman Torso was Voting Page
 
(...) Chris, you seem to by the "torso guy" around here, so if you have a good plan for those pieces, then go for it. And on another note, it has come to my attention that 9326 is NOT the torso number. I really hate to say this, but we need to move (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: 99-03 Voting: Quick Comments
 
(...) That is the same question I had about the construction. :-) And I liked Joshua's logic about the number. It groups them numerically very nicely, and saves using 3-digit #'s, so why not? (...) I would think so - without actually seeing the (...) (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: Discussion-Large Technic Shock 2909c01.dat
 
(...) Why not post it to dat.parts? -- Terry K -- (25 years ago, 13-May-99, to lugnet.cad.dev)
 
  Re: 99-03 Voting: Quick Comments
 
(...) I wish I knew for a _fact_ that this is (was) the case, but I can't say so with any certainty. I would suppose that using an existing mold to create an axle, and then cutting threads into the element, makes a lot more sense than trying to (...) (25 years ago, 13-May-99, to lugnet.cad.dev)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR