 | | Re: 71184 Bar 4.5L Straight is too short
|
|
(...) I don't have the fix, but I did locate it on lugnet.cad.dat.parts. Normally, I'd require you to e-mail me the fix before I'd put it in an official release, but since you're a good modeler, I'll let it go this once. Just don't tell anyone. ;) (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Some Words To BFC
|
|
(...) OK, here's a counter-proposal: don't require all parts/primitives to be BFC'able, and allow both BFC-ready and BFC-not-ready files in the same rendering. This reintroduces the concept of having a single meta-statement at the start of each (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Performance Improvement [DAT]
|
|
(...) As I said before, in this case it's more correct to use 3-4disc primitive, to avoid the T type juntions. (...) Yes, cracks may appear ! Same problem like in a T type junction But has someone said, nothing like real/concrete testing, so here (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Performance Improvement
|
|
Steve: (...) I can't see how Rui's suggested change gives any problems at all and I don't mind a few percent speed increase. (...) And? Does the "diameter line" not cross the radius? If there is a significant risk of a misalignment, then we (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Some Words To BFC
|
|
On Fri, 7 Apr 2000, Leonardo Zide wrote: [...SNIP...] (...) Actually I think you missunderstood something (or maybe I did), but the 0 INVERSE meta command is to be used ONLY with file references, that is: 0 INVERSE 1 16 x y z a b c d e f g h i (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: BFC checking program (was Re: Some Words To BFC)
|
|
I seem to be missing a required .dll file: MFC42D.DLL. Can you send this, or can I find it somewhere else? -John Van (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Some Words To BFC [DAT]
|
|
(...) I don't mind that because I preprocess the files anyway and anyone who wants to get a good speed increase should do the same. But it's not a good idea to turn on/off BFC several times and in some cases, it's nicer to have the faces reversed. (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | BFC checking program (was Re: Some Words To BFC)
|
|
(...) I'm assuming that you're calling "BFC-ready" primitives that have all faces in the same direction. Primitives are not closed volumes so you'll always be able to see the backfaces. (...) I agree technically it doesn't make much difference, I (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Is James' website finally gone for good?
|
|
(...) Good idea. I know James parents are in Europe for another week or so I believe - they get back on something like the 14th if I remember correctly. -Tim (URL) timcourtne ICQ: 23951114 (25 years ago, 7-Apr-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Is James' website finally gone for good?
|
|
Steve: (...) It would be very sad if all his work is lost, so we should definitely offer to host the site on ldraw.org, unless James' parents have another idea. (...) I think we should ask them about it. - And also ask if it is ok to continue the (...) (25 years ago, 7-Apr-00, to lugnet.cad.dev.org.ldraw)
|
