| | Reference Site Inconsistencies
|
|
I was cross-checking some information between LDraw/Partsref, Lutz Uhlmann's Parts Reference, and James Jessiman's Unofficial LEGO Parts Listing. I was specifically looking at the parts with number less than 1000[1], because I need to get a better (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
|
| | Re: getting started making pieces
|
|
(...) Welcome - new part authors are always welcome. The following is my preferred method of doing decorated parts as is a good grounding if you go on to author complete parts - others have had some success with BMP2DAT for decorated parts. 1. (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
|
| | getting started making pieces
|
|
A naive question perhaps, but I can't find the answer anywhere... I want to try my hand at making parts for ldraw, specifically I want to make minifig faces and torsos that haven't been done yet. What program(s) do you wizard-types use to make the (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
|
| | Re: Update 9906
|
|
(...) for (...) sample (...) Yes you're right, and I've done enough torsos that I should not have made such an error. Chris (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
|
| | Re: Update 9906
|
|
(...) You're right, I gave that suggestion some time ago. The subpart only had the back surface when it was using the old number. Leonardo (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
|
| | Re: part 2951, some questions [DAT]
|
|
(...) I will centre between the lower pegholes then. (...) Goood:) (...) correction: I will not put the measurements up, as they are changing as I get along. Look below for more on this. (...) As of now, it looks like the worst part is figuring out (...) (25 years ago, 5-Jan-00, to lugnet.cad.dev)
|
|
| | Re: Update 9906
|
|
(...) I got the fixes. Thanks for the rapid turn-around, Chris! About 973s01 - I don't remember if this subfile ever had a back surface. The name does clearly state that there's no back: "~Subpart Minifig Torso without Front or Back". IIRC, the back (...) (25 years ago, 5-Jan-00, to lugnet.cad.dev)
|
|
| | Re: OMR Planning - Almost There
|
|
(...) (rereading what I wrote) Uh, durrr, that came out as hogwash, didn't it. I meant, if the pages that are created dynamically happen to come out the same as though they had been served statically (IOW, if it's static content generated (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev.org.ldraw)
|
|
| | Re: OMR Planning - Almost There
|
|
(...) Yes. That AND the sort of data you are fetching. In certain cases, a DB engine that has cached the results of queries, coupled with a requesting program that can use the results straightaway, can be faster than a raw filesystem, even if the (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev.org.ldraw)
|
|
| | Re: Update 9906
|
|
(...) Looks like both John and I mistakenly assumed that s\973s01.dat is the torso missing the front surface - in fact it is missing the back as well to cater for those rare torsos with decoration on the back. I sent a corrected version of 973p34 to (...) (25 years ago, 4-Jan-00, to lugnet.cad.dev)
|