 | | Numbers Report - 30 Dec 2003
|
|
Section Totals 118 certified files. 223 files need admin review. 519 files need more votes. 500 have uncertified subfiles. 151 held files. Total Files: 1,511 Comparison with Prev. Report: 2003-12-30: 118 / 223 / 519 / 500 / 151 (1,511) 2003-12-22: (...) (21 years ago, 30-Dec-03, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) I started parts authoring without knowing about BFC. When I read something about BFC-ing here on lugnet, I started to dig myself into it, reading documentation (from www.ldraw.org), trying things out and now I know enough about it. I only (...) (21 years ago, 30-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) I use LDDP and L3Lab with "Poll to L3Lab & LDview" + "Poll to selected line only" turned on. going through the code with CRTL+W (orion please don't forget my special request) rewinding what's needed. w. (21 years ago, 30-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC? [DAT]
|
|
(...) For the two-dimensional primitives (disc, ndis, ring, chrd) you can do the following: Say you have a disc in the x-z plane, like: 1 16 0 0 0 10 0 0 0 1 0 0 0 10 4-4disc.dat If this has the wrong BFC winding, you can just flip (mirror) the (...) (21 years ago, 30-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) I use Notepad (NOTEPAD.EXE), until the DAT file gets too huge, whereupon I use WordPad (WORDPAD.EXE) to continue editing the file. I use a calculator and scratch paper (to do a rough sketch and to keep notes of important locations). Whenever I (...) (21 years ago, 30-Dec-03, to lugnet.cad.dev)
|
| |
| | Need partnumbers and some partnames
|
|
Now the parts update 2003-03 is released, I started to make some parts I have already created ready for upload to the parts tracker. I need partnumbers for the following parts. I also want to know if the partnames are correct. * Technic Brick 1 x 2 (...) (21 years ago, 29-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: BFC And Mirroring (LDS)
|
|
(...) Thanks Steve. :) (21 years ago, 29-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) OK - it's not a technique I use, but in an email conversation recently somebody convinced me that inverting the matrix would switch the winding. Now that I test it again I found I was mistaken. Chris (21 years ago, 28-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: BFC And Mirroring (LDS)
|
|
In lugnet.cad.dev, Tore Eriksson wrote: [snip] (...) Yes. Steve (21 years ago, 28-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
In lugnet.cad.dev, Chris Dee wrote: [snip] Thanks for writing this up, Chris! Your explanation was very good in all respects except for one small point: (...) Actually, negating the transformation matrix should not invert any object; and even if it (...) (21 years ago, 28-Dec-03, to lugnet.cad.dev)
|
