 | | Re: new part - 71014 - castle greatsword - revised
|
|
Franklin W. Cain <fwcain@yahoo.com> wrote in message news:20000328190244....ail.com... (...) Nice work on the quillions (I'm sure that was fun:), and the handle is much improved, too. Just a few nits to point out: Where you extended the cylinder on (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 6641.dat Technic Changeover Catch
|
|
(...) I agree with you Fredrik, but to modelise this part, I used the same orientation as in the mockup made by Jonathan Wilson. Changing this orientation will change the models using this part. So could we change the orientation of a part if the (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Throwbot foot
|
|
(...) Fredrik you are right, the axle is too thin. Steve, the reason is because I modelise the parts with a CAD CAM program then I convert the part to dat with my program STL2AT. For the moment, this program recognize only cylindric primitives. I (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: looking for 3425
|
|
(...) Apparantly. I cannot find the part number in any parts reference, so what i it? /Tore (25 years ago, 28-Mar-00, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | new part - 71014 - castle greatsword - revised [DAT]
|
|
I updated this DAT file, incorporating all the suggestions that I received. Please LMKWYT. Thanks, Franklin 0 Castle Greatsword 0 Filename: 71014.DAT 0 Author: Franklin W. Cain (fwcain@yahoo.com) 0 Unofficial Element 0 0 CATEGORY Minifig Accessory 0 (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New part : Minifig Torso with Patch Pocket Pattern
|
|
Chris Dee <chris_w_dee@hotmail.com> wrote in message news:Fs56r5.1Gu@lugnet.com... (...) The (...) that (...) than (...) I would say keep using the technique. Minifigs are most often viewed in models at a distance where they look better with the (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New part : Minifig Torso with Patch Pocket Pattern
|
|
(...) I noticed that too, but dismissed it as a rendering artifact, which I suppose it is. Do you think this means we should stop using this technique? The town torsos I have done without the hidden lines look bad in L3Lab at low mag - so I was (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Throwbot foot
|
|
(...) Marc, Fredrik's post prompted me to look more closely at this part. I noticed that there are references to any of the axle primitives. Is there a reason you did not use any of these primitive files in your file? Steve (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Throwbot foot
|
|
To me, the axle sticking out from the centre of the foot appears to have a little bit too thin cross sections. This observation is only based on viewing the part in L3Lab, so it may be wrong. What do you think? Other than that, it looks good! (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 32165 Technic Throwbot Head
|
|
Wow! What a part! Great work! If there is one thing I can nitpick about, it would be the lower "partial" axle hole. The real part has two small "nibs" on the lower portion, which are used to hold an axle in place. You can hear a "click" sound if (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 6641.dat Technic Changeover Catch
|
|
This part certainly looks very good! I'm a bit unsure about it's orientation, though. Perhaps it could benefit from having the same orientation and origin as "32039 Technic Connector with Axlehole" and "3651 Technic Connector"? The part does have (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 6539.dat Technic Driving Ring
|
|
The part does not appear to have the "clip" detail which is seen in the centre of the real part. But the part still looks great, so I would definitively vote for it in the LCAD update. Great work! I also agree with your choice of orientation. (I (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | 6539.dat Technic Driving Ring [DAT]
|
|
0 Technic Driving Ring 0 Name: 6539.dat 0 Author: Marc Klein 0 Created with stl2dat conversion tool 0 Un-Official LCad part 1 16 0 0 9 20 0 0 0 0 20 0 -4 0 4-4cyli.dat 1 16 0 0 9 20 0 0 0 0 20 0 -1 0 4-4edge.dat 1 16 0 0 5 20 0 0 0 0 20 0 -1 0 (...) (25 years ago, 28-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 6631.dat Technic Changeover Plate
|
|
Marc Klein <marckl@easynet.fr> wrote in message news:38de6aa6.717081...net.com... (...) Looks great! -John Van (25 years ago, 27-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New part : Minifig Torso with Patch Pocket Pattern
|
|
Chris Dee <chris_w_dee@hotmail.com> wrote in message news:Fry8p1.1MF@lugnet.com... (...) Very nice. I noticed something interesting when viewing this part. The shading in L3Lab and LDLite is not applied to edgelines, so the white edgelines in the (...) (25 years ago, 27-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: new part - 71014 Castle Greatsword
|
|
Franklin W. Cain <fwcain@yahoo.com> wrote in message news:FrxKs8.IGz@lugnet.com... (...) Franklin, Thanks for your committment to creating quality parts! I predict you will become a true part artist! -John Van (25 years ago, 27-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | 6641.dat Technic Changeover Catch [DAT]
|
|
0 Technic Changeover Catch 0 Name: 6641.dat 0 Author: Marc Klein 0 Created with stl2dat conversion tool 0 Un-Official LCad part 1 16 10 22 0 0 -20 0 2 0 -3.46 3.46 0 2 1-4cyli.dat 1 16 10 22 0 0 -1 0 2 0 -3.46 3.46 0 2 1-4edge.dat 1 16 -10 22 0 0 -1 (...) (25 years ago, 26-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | 6631.dat Technic Changeover Plate [DAT]
|
|
0 Technic Changeover Plate 0 Author: Marc Klein 0 Name: 6631.dat 0 Created with stl2dat conversion tool 0 Unofficial Element 1 16 0 4 -40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 10 0 -30 1 0 0 0 1 0 0 0 1 stud2.dat 1 16 -10 0 -30 1 0 0 0 1 0 0 0 1 (...) (25 years ago, 26-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | New part : Minifig Torso with Patch Pocket Pattern [DAT]
|
|
Here is the old Town/Train workman torso. Please LMKWYT - Chris 0 Minifig Torso with Patch Pocket Pattern 0 Name: 973p24.DAT 0 Author: Chris Dee (chris_w_dee@hotmail.com) 0 Unofficial Element 1 15 0 2 -10 1.25 0 0 0 0 1.25 0 1 0 4-4disc.dat 1 16 0 2 (...) (25 years ago, 24-Mar-00, to lugnet.cad.dat.parts)
|
| |
| | Re: new part - 71014 Castle Greatsword
|
|
(...) It's there. Try again. Or go to my main page: (URL) and follow the link from there. Steve (25 years ago, 24-Mar-00, to lugnet.cad.dat.parts)
|
