 | | Creating 47457.dat 2x2x2/3 Sloped&Rounded
|
|
(...) I'm not a kid any more (I'm 37) and am quite new in the community. One of my deep desire is to contribute to the community by starting part authoring. So if you plan to write a tutorial (for kids it is perfect), easy to follow, about your (...) (20 years ago, 20-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Creating 47457.dat 2x2x2/3 Sloped&Rounded
|
|
(...) My goodness, that was one massive scary part! I'm going to look that up and see how many lines it took! I would have chosen the click rotation joint. I figured I needed a very simple part to warm up. Talking about "not too far off", should I (...) (20 years ago, 20-Sep-04, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: Creating 47457.dat 2x2x2/3 Sloped&Rounded
|
|
(...) Ah, conditional lines! I didn't even think about those. Thanks! I'll look into it and see if I can figure it out. I'll also learn how to use Show All Edge Lines. By the way, the part is common to 3 of the large good guys of Knights Kingdom. I (...) (20 years ago, 20-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Creating 47457.dat 2x2x2/3 Sloped&Rounded
|
|
Congratulations on initial completion of your first part. (...) I don't have this part (at least I don't think), so I can't comment on the accuracy of the geometry. However, I can comment on three things I saw. First, it looks like you used color 16 (...) (20 years ago, 19-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Creating 47457.dat 2x2x2/3 Sloped&Rounded
|
|
(...) submission (as soon as parts@ldraw.org lets me). (...) Looks good. You chose a relativle simple part for your first, unlike me: [LDrawPart 2618:7] (...) Don't worry about those. They're non-funtional and insignificant (...) Guessing is fine as (...) (20 years ago, 19-Sep-04, to lugnet.cad.dat.parts, FTX)
|
| |
| | Creating 47457.dat 2x2x2/3 Sloped&Rounded [DAT]
|
|
Finally, my fair (if not terrible) first attempt at part authoring is ready for submission (as soon as parts@ldraw.org lets me). What a learning experience! It took 12 version saves to get "close". And I'm sure there's more to learn after the (...) (20 years ago, 19-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Castle Knights helmet
|
|
(...) Hi everyone. I have posted images of the Knight's Visor and large feather on: (URL) (20 years ago, 15-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: 47457 2 x 2 x 2/3 Two Top Studs, Curved Slope End
|
|
(...) I think I'll just create one part of it all. I don't think a primitive nor a sub-part would be necessary. Thanks. (20 years ago, 14-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: 47457 2 x 2 x 2/3 Two Top Studs, Curved Slope End
|
|
(...) Are there many parts that will need this surface? It doesn't seem like it would be that common... If it would help you to have a subfile, then create a subpart file rather than a primitive. If I've totally missed the point of your question, (...) (20 years ago, 13-Sep-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Question on part naming
|
|
(...) If you look at what group this is (and the group charter), you'll see that my question applies only to the LDraw parts library, and not to any official LEGO naming convention. I'm looking for an official LDraw answer. As it happens, I am an (...) (20 years ago, 13-Sep-04, to lugnet.cad.dat.parts)
|
