 | | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) I originally thought that the numbers were based on the Lego numbers, but my (admittedly brief) research told me that they didn't, as I found no matches out of about 6 pieces. I realize that parts will often change numbers (how many System 2x4 (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner" [DAT]
|
|
(...) OK, Steve, how about this? If this is OK, LMK, and I'll email you this updated version. ;-) Thanks, Franklin 0 Minifig Hat Tri-Corner 0 Name: x475.dat 0 Author: Franklin W. Cain <fwcain@yahoo.com> 0 Unofficial Element 0 0 CATEGORY Minifig (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Or, at least, replace the paragraph of comments with something like: 0 To put a feather on the hat, use the following line: 0 1 15 0 -10 -12 1 0 0 0 1 0 0 0 1 XXXXa.dat The suggestions about using subfiles are accurate, but it's not (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4
|
|
(...) Strange. I named the Scala stud to Stud5.dat, but someone renamed it to StudSc.dat. So I thought StudDu*.dat would follow that new pattern... Please note that there are solid Duplo studs on some Duplo baseplates, even though the most common (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3001_d.dat - Duplo Brick 2 x 4 [DAT]
|
|
(...) To find the correct part number, take a DUPLO 2x4 and examine the underside. There should be a 4 or 5 digit number stamped into the part, usually on the underside of the top. This is the part number. (...) standard. The next available number (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: x475.dat, "Minifig Hat Tri-Corner"
|
|
(...) Could you provide an additional "comple shortcut"? I think it would make working with your part easier for other people. Btw, the hat, as seen on brickshelf, looks fine ;-) Regards, Hakan (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: work-in-progress: pirate tri-corner hat
|
|
(...) ("(URL) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | x475.dat, "Minifig Hat Tri-Corner" [DAT]
|
|
As promised elsewhere ("(URL) is the finalized version of the pirate's tricorner hat! ;-) I hope y'all like this, 'cuz it took me several months (on and off) to do this one! :-P For reference, if you'd like to use this with the small feather-plume, (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Duplo parts?
|
|
(...) No, it's correct. If they were thicker, you wouldn't be able to put Duplo bricks on top of System bricks. (...) The stud height has changed over the years. The newer ones are quite close to 11. I haven't checked the older ones that closely. (...) (24 years ago, 5-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Duplo parts?
|
|
In lugnet.cad.dat.parts Steve Bliss wrote... (...) Yup... :) (...) There is: Primitive substitution! I found out that we (mis)use stud4.dat by scaling its height by 5 in bricks! (and other factors in other parts) If I add a rounded edge to (...) (24 years ago, 4-Jan-01, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
