Subject:
|
Re: Overlapping polygons etc
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Wed, 6 Aug 2003 11:41:48 GMT
|
Viewed:
|
747 times
|
| |
|
|
In lugnet.cad, Paul Easter wrote:
> In lugnet.cad, Ross Crawford wrote:
> >
> > Well yes and no - that sentence actually asked 2 different questions :) but both
> > will be solved if I inline the studs and trim the cylinders as Orion suggested
> > (I think).
> I actually would not recommend that.
>
> >
> > Thanks for your help guys! (Even if it means more work for me...)
> >
> > ROSCO
>
>
> Paul
>
>
> Example below:
>
> 1 16 0 4 10 1 0 0 0 2 0 0 0 1 stud2a.dat
> 1 16 0 4 10 4.2426 0 4.2426 0 1 0 -4.2426 0 4.2426 3-4edge.dat
> 1 16 0 4 10 5.5433 0 -2.2961 0 12 0 -2.2961 0 -5.5433 3-8cyli.dat
> 1 16 0 16 10 5.5433 0 -2.2961 0 1 0 -2.2961 0 -5.5433 3-8edge.dat
> 1 16 0 4 10 4 0 0 0 1 0 0 0 4 4-4edge.dat
> 1 16 0 4 10 4.243 0 4.243 0 1 0 -4.243 0 4.243 3-4edge.dat
> 1 16 -10 10 6 5.5 0 0 0 0 6 0 1 0 rect.dat
> 0 reference info
> 1 1 10 10 6 5.5 0 0 0 0 6 0 1 0 rect.dat
> 4 1 18 4 13 18 4 6 -18 4 6 -18 4 13
> 4 1 14 4 18 14 4 13 -14 4 13 -14 4 18
> 4 1 16 16 6 16 16 -6 -16 16 -6 -16 16 6
> 4 1 14 4 18 14 0 18 -14 0 18 -14 4 18
> 2 2 14 0 18 -14 0 18
> 4 1 14 0 18 16 0 20 -16 0 20 -14 0 18
> 2 2 16 0 20 -16 0 20
OK, using your example as a guide, I finished off the part. First cut is at
http://www.brickshelf.com/gallery/RoscoHead/cad/30518.dat
I did notice, though, that using LDview, there is a definite line where the
studs join the cylinders. I tried rotating the studs by 22.5 degrees to match,
but the line remained. It only becomes visible at fairly high zoom, and at
certain angles, so I figure it's acceptable. It also looks fine in MLcad (to my
eyes) even when transparent. Comments?
ROSCO
|
|
Message has 1 Reply:
Message is in Reply To:
 | | Re: Overlapping polygons etc [DAT]
|
| (...) I think I missed what you meant earlier. I would not inline the stud for that, Unless it was a major piece of the part. which this is not. (...) Ok, I see it now. My laptop screen was not showing me enough detail. See my example below. I used (...) (21 years ago, 6-Aug-03, to lugnet.cad)
|
9 Messages in This Thread:
 
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
