 | | Re: Colinear Vertices
|
|
(...) triangle has had its surface normal pulled down. So the triangle isn't co-planar with the quad as far as the lighting is concerned. With curve smoothing, all polygons who share a smoothed vertex use a common surface normal for that vertex. But (...) (16 years ago, 13-Dec-08, to lugnet.cad)
|
| |
| | LD4DStudio suggestions?
|
|
Hello all, I was wondering if people have some minor suggestions / bug reports for my current LD4DStudio version. Work on the 1.1 version is taking longer than expected so I was planning to release a bugfix only version this month. Any additional (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Conditional Ring primitive?
|
|
(...) My comment about needing twice the geometry for the edge was based on a misunderstanding of what you wrote. Based on what I now assume you meant, two wouldn't be required for each joint. However, your solution would only work if the cones on (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Conditional Ring primitive?
|
|
(...) It sounds like it would work, but I'm not sure if people would go for it. Of course, if the POTM competitions are anything to go by, you're making a majority of the complicated parts right now, so if you go with it, that's probably all we need (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Conditional Ring primitive?
|
|
(...) Mmhhh... maybe by setting 2 conditional rings on the junction. Each condring would be set between a cylinder and a cone. Scaling the ring would adapt to various cone slopes. Of course 2 rings would be needed, one for converging cones, one for (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Conditional Ring primitive?
|
|
(...) That's a primitive I have been longing for... but I realized it is impossible to build: where would you put the control lines? The top control points would need to be scaled differently from bottom ones to match various cylinders/cones (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Conditional Ring primitive?
|
|
(...) I just noticed something else while investigating a fix for the above problem. The above model could really use a circular conditional edge primitive. I would vote for x-ycedge.dat as the filename (ie 1-4cedge.dat, 4-4cedge.dat, (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: Colinear Vertices
|
|
(...) I played with the settings, and I had to set the precision all the way down to 0.133 in order to get it to fully smooth. (0.125 failed to smooth properly.) (...) .005. I think I'll set the precision to .01, to hopefully give it some leeway. I (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
| |
| | Re: LETGUI new version 0.1.0.18
|
|
(...) Thanks! For the record: - Ytruder 1.2 is no longer limited to Y direction and can extrude along x, y or z directions - Intersector 1.3 has a new scaling option that improves result for small parts. Philo (16 years ago, 12-Dec-08, to lugnet.cad.dev)
|
| |
| | Re: Colinear Vertices
|
|
(...) It makes sense! (...) An example, this button: (URL) I rounded condlines to 2 decimal places since I couldn't get smoothing anyway. I did more experiments, with full precision in condline it works: (URL) but after rounding to 3 dp there is no (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
