 | | Re: ... & national flag
|
|
(...) Look here... (URL) (22 years ago, 17-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | LDraw Torso Generator
|
|
I'm not quite sure where to post this. I'm working on a program that opens an image file and generates an LDraw torso based on it. It's not ready for release yet, but there's some pictures that demonstrate the results on my page. Right now the (...) (22 years ago, 17-Sep-02, to lugnet.announce, lugnet.cad)
|
| |
| | Re: Printable Partsref
|
|
Sorry about the late reply, but thanks! Peace and Long Life, Tony Alexander (22 years ago, 17-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
I'm going to mostly stay out of this discussion for now. I will throw out a few suggestions/requirements, though: 1. The final definition should be renderable by ldraw.exe. 2. It might be a good idea to put each 'synthesizable part' in its own file (...) (22 years ago, 17-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: BrickDraw3D bleeda
|
|
Version 0.3 has been revised again. Parts in parts list drag to model in color (useful). They drag out as full lines of DAT (not much use). No dragging from model view. Betta than the last build (not all are.) (URL) (22 years ago, 17-Sep-02, to lugnet.cad.dev.mac)
|
| |
| | Re: keep it up
|
|
(...) Yeah, but do you want to hear about them? Chris :) (22 years ago, 17-Sep-02, to lugnet.cad.dev.mac)
|
| |
| | Re: I need help on Delphi so I can finnish my program
|
|
(...) Here's a better way (I think, I haven't tested it yet); Use ExtractStrings as stated above and change the string you want to change. Then set the Delimter Property to ' ' set the QuoteChar Property to '' use the DelimitedText property to (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: *** LDView Version 1.9.7 Released ***
|
|
"Travis Cobbs" <tcobbs@REMOVE.halibut.com> skrev i meddelandet news:H2JHFL.J55@lugnet.com... (...) So use the possibilities of the unix file system to your advantage - the first time you find a file the hard way, create a _link_ to it, with your (...) (22 years ago, 16-Sep-02, to lugnet.cad)
|
| |
| | Re: I need help on Delphi so I can finnish my program
|
|
(...) Sorry I do understand is only that I don't like the ansewr. But I'll see what I can do. (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
(...) I suspect your problem was that you were confused by the technical jargon of "Bend Thingie." 8^) Dave! (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
(...) Yes! That's the one! Good to know my memory hasn't *completely* gone soft in my old age... <grin> JohnG, GMLTC (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
(...) This? (URL) Dave! (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: I need help on Delphi so I can finnish my program
|
|
(...) Please don't take this the wrong way, but if you didn't understand what he wrote, then you would probably find it a lot less frustrating to spend some more time learning how to use Delphi, and programming techniques in general. I've never (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
(...) Iterative solving requires a model and a way to compute how far it is from a desired state and a way to compute how to take a tiny step toward the desired state. You loop over tiny steps, updating the model, until either X steps are taken, the (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: *** LDView Version 1.9.7 Released ***
|
|
(...) That's a good idea, but since LDView caches files after reading them, it will only ever check for any particular file once. So I don't think this will help. It might help, though, since I would essentiall scan the entire LDraw parts directory (...) (22 years ago, 16-Sep-02, to lugnet.cad)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
In lugnet.cad.dev, Kevin L. Clague writes: <snip1> (...) <snip2> Someone posted something similar to this a while back, but I can't find it... They were demonstrating rendering (POV-Ray, I think) LEGO flexible tubing by defining it as a computed (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Formalizing a method for handling synthesizable parts
|
|
Erik, I think that for tube like devices, the constraints will be vectors that indicate some part of the tube needs to be at this location and at this orientation. The endpoints are like this. This constraint mechanism works well for routing wires (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Maersk parts & national flag [DAT]
|
|
(...) It will fit on a flag. Jeroen BTW Thomas Burger did some parts and also a logo (in BMP2DAT): (URL) maersk star 0 Name: maersk_star.ldr 0 Author: jeroendehaan@mac.com 0 Unofficial Model 3 15 4.7129 -1.3379 0 2.0826 -4.6094 0 10.066 -8.2705 0 3 (...) (22 years ago, 16-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: I need help on Delphi so I can finnish my program
|
|
I don't understand this hope there is another easy way. (...) (22 years ago, 16-Sep-02, to lugnet.cad.dev)
|
| |
| | Re: Call out for an airplane or helicopter model
|
|
(...) You are welcome to use "Sal Colibri": (URL) well, Jacob (22 years ago, 16-Sep-02, to lugnet.cad)
|
