 | | Re: I want a ldraw poster
|
|
"Eduardo Vazquez Harte" <eduvazhar@terra.es> wrote in message news:GLzLrB.6yL@lugnet.com... (...) Hi Eduardo - What do you mean by 'poster about LDraw?' Do you want a rendering for printout on a poster, do you want a poster with an overview and (...) (23 years ago, 29-Oct-01, to lugnet.cad)
|
| |
| | Need new Ldraw parts file, but can't get to site!
|
|
Hello, I cannot get to the ldraw.org site for some reason; it's probably my ISP. I cannot use any of the alternatives such as anonymizer or safeweb because of some corporate firewall. I want to get the new Ldraw.org Parts Update. Is there anywhere (...) (23 years ago, 29-Oct-01, to lugnet.cad)
|
| |
| | Re: custom 73590a hose flexible
|
|
(...) If you know emacs, try Fredrik Glöckner's emacs ldraw mode. Even if you don't know emacs, he has good instructions at (URL) instructions for doing hoses (and bezier curves in general) are about halfway down at (URL) used it for the hoses on my (...) (23 years ago, 29-Oct-01, to lugnet.cad.mlcad)
|
| |
| | Re: Top 10 posters in lugnet.cad.dev
|
|
(...) I'm not the biggest poster in .general either. I hardly every post there at all! (Grin, duck, run... repeat as needed) ++Lar (prolific but not profligate) (23 years ago, 29-Oct-01, to lugnet.cad.dev)
|
| |
| | Re: Top 10 posters in lugnet.cad.dev
|
|
(...) <snip> How about for all of LUGNET? Isn't it time to see who's the chattiest of them all? (perhaps an annual thing around LUGNET's anniversary date?) -John (23 years ago, 29-Oct-01, to lugnet.cad.dev)
|
| |
| | RE: Top 10 posters in lugnet.cad.dev
|
|
(...) No, in general. I just left the post in cad.dev cause that's where it started. --Bram Bram Lambrecht bram@cwru.edu www.bldesign.org (23 years ago, 29-Oct-01, to lugnet.cad.dev)
|
| |
| | Re: Top 10 posters in lugnet.cad.dev
|
|
(...) In cad.dev??? I am hardly a big time poster here. And yes I am slacking. Darn work is intruding again. (23 years ago, 29-Oct-01, to lugnet.cad.dev)
|
| |
| | Re: 8219 cart
|
|
Hallo Ruediger "Ruediger Dietloff" <Ruediger_Dietloff@yahoo.de> schreef in bericht news:GLyw41.8H1@lugnet.com... (...) I just looked at it and it looks quite nice! Just a question: why do you start with the 6x2 plates? About the brake dish: it is (...) (23 years ago, 29-Oct-01, to lugnet.cad.dat.models.sets)
|
| |
| | I want a ldraw poster
|
|
Where cad I dowload a A4 size poster about ldraw (23 years ago, 29-Oct-01, to lugnet.cad)
|
| |
| | custom 73590a hose flexible
|
|
I have been trying to make custom bent flexible hose part 73590a using parts 750 (hose flexible end 1 x 1 x2/3 with tabs) 754 (hose flexible segment link section)755 hose flexible segment end section)and 756 hose flexible segment centre section) (...) (23 years ago, 29-Oct-01, to lugnet.cad.mlcad)
|
