 | | Re: new lego-cad part: x474.dat, "Arm Piece with Towball and Stud"
|
|
(...) Looks good. Has TLC made variations on this part? Seems like I recall discussion of an older and a newer version, but I don't remember clearly now. (...) I'm not understanding where you're coming from with this comment. All the towball parts I (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) Very nice job on these parts! I think I'd name the cannon parts as: 2527.DAT Minifig Cannon 2 x 4 Base x518.DAT Minifig Cannon 2 x n Non-Shooting Sorry, I don't have a cannon handy for measurement -- replace the 'n' with the proper length. (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: endparts
|
|
Could you center them around the Y-axis? Also, I don't now if I schould make the airtubes hollow or not, some purist might say yes, but you would never see it and it would take up twice as much space. Any suggestions? thanks a lot, koen. John (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | RE: L3PAO update (v 1.3)
|
|
(...) URL? --Bram Bram Lambrecht bram@cwru.edu (URL) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
| |
| | L3PAO update (v 1.3)
|
|
When using L3PAO to do the Beretta this week, I noticed a few issues here and there, so I compiled an update. (URL) 1.3 ---...--- Fixed yet another error in the command line generator. If the path to l3p was the same as the path to L3PAO, it was (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
| |
| | (canceled)
|
|
|
| |
| | Re: License - again
|
|
In lugnet.cad.dev, Bram Lambrecht writes: [snip] (...) Filip Spacek did the conversion. (...) It would be great if when/if MLCad started allowing plugins, someone wrote a converter to POV which worked directly in MLCad. This would make life a bit (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev, lugnet.cad.mlcad)
|
| |
| | Re: License - again
|
|
"Bram Lambrecht" <bram@cwru.edu> wrote in message news:MABBIBJJFOJIOHD...wru.edu... (...) part in (...) The (...) relied (...) wrote (...) not (...) different. (...) LDraw (...) directly. (...) Thanks for the correction and lists. John Van (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: endparts
|
|
I'll be doing this in the next day or two. -John Van "koen" <koen.jordens@studen...ven.ac.be> wrote in message news:G5D49F.FpA@lugnet.com... (...) place (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | RE: License - again
|
|
(...) Actually, L2P uses the LGEO library written by Lutz Uhlman. Lutz also wrote L2P and all the textures that LGEO uses. AFAIK, Anton Raves has no connection with L2P at all. It's difficult to use Anton's parts because not only the coordinate (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
