 | | Re: Brickbay Temp URL Available
|
|
You just start LDLite from a command prompt, with a -MS option. MS is for "Mode Save". Something like: c:\ldraw\ldlite\ldlite 3001.dat -MS (assuming LDLite is installed in c:\ldraw\ldlite\) Steve (...) (24 years ago, 30-May-00, to lugnet.market.shopping, lugnet.cad)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) typo typo... yes, I meant to say I can't be on the committee. I guess if I were committed, I'd have lots of time... if I could only convince my therapist to allow LEGO as therapy. (...) take that to off-topic.debate, it's debatable. (...) (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Put me down for a minumum of 100 USD (and like Larry, I'm good for more if it is necessary to get the project off the ground). (...) I know some people say you should be committed Larry, but that's not what we're talking about... Tim just (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) be (...) at. I (...) Ya, right after I pressed fire I realised it was a bit cryptic. Lets try again. What is "at cost"? (we all agree that it makes sense to press 1000 of them because that's where the cost per starts to get cheap) One *could* (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Thanks! (...) I'm not completely undersrtanding... I know that 50 at cost is what they asked me for in an email - could you clarify 1000/1050? I *think* I understand what you're getting to but I'm not 100% sure. Its 5am. -Tim (URL) timcourtne (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) :( You're going to miss some serious festing....hope you can make it . (...) Sure there is. To lighten my load travelling, either you could send them with John Neal, or ship them to Terry K or Mike P. When you get ready to loan them out we can (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | Re: [Part] 4515p03.dat - Slope Brick 10 6 x 8 with Slate Roof Patt ern
|
|
(...) Can someone else try looking at both the first and second versions of hte part and see if they see bleedthrough? It might have been me. I was viewing it with MLCad 1.7 ++Lar (24 years ago, 29-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: LDraw CD-ROM Update/Funding and dealing with group funds
|
|
(...) Put me down for a minimum of 200 USD in funding for this. If we come up short, I'm in for up to 500. I would prefer that others cover it though if at all possible. I don't have time to be on the committed, though. The reimbursement procedure (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDraw to display at Legoland California for Kidvention
|
|
(...) most (...) such (...) imagination. (...) don't (...) Thanks for the clarification! I think you're spot on. (...) That sounds pretty swell. (...) generated (...) I do have physical models for all of that except the blue version of the hopper. (...) (24 years ago, 29-May-00, to lugnet.cad.dev.org.ldraw, lugnet.legoland.california)
|
| |
| | Re: 32198 Technic Gear 20 Tooth Bevel
|
|
Good part! However, to match the orientation of the previous bevel gear, it should be rotated 180 deg around the Y axis. I would also prefer that it was centered in the origin. Right now it is centered in Z=5. Fredrik (24 years ago, 29-May-00, to lugnet.cad.dat.parts)
|
