| | RE: M68HC711E9
|
|
O.K, , I still have a question. I'm working with a handy board and it use a special mode to talk to a LCD. If i understand , the handy board need to put the reset vector in the range BFC0 - BFFF. If get the aplication note for the 711E9 and ,as it (...) (27 years ago, 17-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Still problems to boot handyboard.
|
|
I still have problems with two handyboards. I can download the code but never boot my code (that code run in other handy, however) Other variant is if i put a 69hc11a1fn the handy download the initiatl bootstrap code , and when try to syncronize (...) (27 years ago, 17-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Re: Shaft Encoders
|
|
(...) Hi there, Would these chips be suitable for interfacing a mouse to the Handyboard? My robot incorporates a mouse as a castor wheel and I want to use its shaft encoders as position/velocity sensors (relative) for the robot, but I don't know (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Re: Shaft encoder
|
|
(...) Hi there, Would these chips be suitable for interfacing a mouse to the Handyboard? My robot incorporates a mouse as a castor wheel and I want to use its shaft encoders as position/velocity sensors (relative) for the robot, but I don't know (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Handy board troubles.
|
|
I have various handyboard and i never use the IR ports. So i'm assembling one handy, and don't put al the components asociated to that ports. I download anyprogram to that's board and never boot again!!!! The transmision is o.k. but don't start (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Re: Config Register error
|
|
I had the same problem. I was never able to get HBDL to set the config register. I used DL to set it on one board and DLM on another. I used the information from the HandyBoard technical reference manual to use these programs. (URL) the config (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Config Register error
|
|
hello all, I have only started building the Handy Board and have run into some problems at the very start when i first conected the part built board. I have build it as far as the power supply, stop switch and 68hc11 installed, memory and lcd. When (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Hooking up PA7
|
|
I downloaded the 9600 baud serial driver that uses Digital input #9 or PA7 (I think). It is really unclear to me which connector I should plug into. In between the IR I/O section and the BATTPWR LED's there are a bunch of connectors. The manual (...) (27 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
|
|
| | using handyboard with vernier ULI
|
|
Hello from New Mexico I'm currently teaching a robotics class at the high school level and we have been exploring the possibility of creating a rover that will eventually be independent and have enough AI to make decisions that will get it through (...) (27 years ago, 15-Jan-98, to lugnet.robotics.handyboard)
|
|
| | Initialization Problemas. S.O.S.
|
|
Hello Out there! We are a group of computer science students here in Universidad Simon Bolivar (Caracas, Venezuela). We are currently teaching a robotics course as we took it last trimester. We are having trouble initializing the handyboards. The IC (...) (27 years ago, 15-Jan-98, to lugnet.robotics.handyboard)
|