 | | pcode_hb download problem. Please Help me.
|
|
I have a big problem to download pcode_hb.S19 on my Handy Board. The download looks like OK. I have this message on my PC Screen. 6811 .s19 file downloader. Version 7.31 Aug 3 1994 Copyright Randy Sargent 1994 Using port com1 Please place board in (...) (27 years ago, 16-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Tone generator questions
|
|
hello. I'm reading through the Robot builders bonanza, and I'm on pp.266. On the bottom of the page (fig. 30-16), there is a tone generator that will generate 2 ones. As printed, theres a chip (4071) that limits only one of the tone jenerators to (...) (27 years ago, 16-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Looking for cables
|
|
Mouser Electronics has a good selection of connectors that work well on the handyboard. They can be found at: (URL) (27 years ago, 15-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Downloading Problems
|
|
I know that the cable works because a person I know has used the modem cable succesfully with their handyboard. Also, I have done a continuity check on the wires in the cable and comparred them to what Apple says is a modem cable, and it is (...) (27 years ago, 15-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloading Problems
|
|
1. don't worry about the slightly out of spec voltages, +/- 5% is just not a problem. 2. you have already demonstrated that your board HW is OK by communicating from a Windows system. therefore 3. it is probably a cabling problem from your mac. you (...) (27 years ago, 15-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Downloading Problems
|
|
Hello all, I am in the process of building my Handyboard. I have installed the CPU and some of the voltages seem suspect. For example the E-clock signal seems to be about 2.3 volts and the main system power measured at the +5 Volts terminal for the (...) (27 years ago, 15-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Vision
|
|
(...) The article I saw it in was by Steve Ciarcia, in Byte Magazine, and entitled something like "The Micron Eye". Check through Byte magazine indexes and you should find the article. The Micromint company sold kits for it, might still. Curt Mills, (...) (27 years ago, 13-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Looking for cables
|
|
I am having difficulty finding cables to connect to the headers on the Handy board. Specifically, I would like to find a 14-pin cable with a male end to connect the handy boards LCD header (U4) and a female end to connect to a header I have (...) (27 years ago, 13-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Interfacing a clock chip?
|
|
Hi folks. Has anyone had any experience/success with interfacing a Motorola 6818 or 6818A clock chip to the 68HC11? I have some of both of these chips and would like to put them to use. Does anyone know the difference between the 6818 and the 6818A (...) (27 years ago, 12-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Error downloading Pcode in DOS
|
|
Hi, I'm using dl in DOS. I recently assembled a new HB but I cannot download the Pcode to the HB. DL gives me this error message: Downloading 256 byte bootstrap (229 data) ......... ......... ......... Timeout on serial recieve. 1 chars left to (...) (27 years ago, 12-Oct-97, to lugnet.robotics.handyboard)
|
