 | | Train Table Height [was: Discussion of Train Table Sizes]
|
|
(...) To the best of my knowledge, no. General model railroading practice seems to be 36 inches. Some LTCs use this height. Most clubs of which I know use 30 inches (this is the nominal height of banquet tables, and easily achieved with standard (...) (20 years ago, 15-Dec-04, to lugnet.trains.org)
|
| |
| | Re: GFLTC at GATS Tampa this weekend (Dec 18-19)
|
|
Note: wrong dates listed... It should be December 18-19, 2004. (...) (20 years ago, 15-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | GFLTC at GATS Tampa this weekend
|
|
Hi all, The Greater Florida LEGO Train Club will have a layout at the Great American Trains Show (GATS) December 11-12, 2004 in Tampa, Florida. The 28ft X 16ft layout will feature two main lines of trains, a Monorail line, a large yard area, a large (...) (20 years ago, 15-Dec-04, to lugnet.announce, lugnet.trains, lugnet.trains.org, lugnet.loc.us.fl, lugnet.org.us.gflug)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Hi all, I did use the measure of 30 and 7/32nds, with gives us 767,55625 millimeters, and rounded them up to 768mm. This is indeed a bit too much, because we got also problems with bridges (96 studs long) mounted on a table 30 bricks below the (...) (20 years ago, 14-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
The GMLTC uses 40"x60" plywood tables with custom-built aluminum frames underneath and heavy-duty folding legs. Some pros and cons: - Pro: Plenty of room! After we trashed our last layout, we consciously decided to build "larger" this time: 8-wide (...) (20 years ago, 14-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Funny you should mention that. I just bought 6 of that very type of banquet table for the traveling TCLTC layout yesterday ($41 each from Costco). I really like these tables and am excited about using them. I should also say that we've also (...) (20 years ago, 13-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Kevin- That's an unsolved problem for us that gets worse when we are in a hurry and as the layout gets larger. When we are not rushed, we losen the bolts a little and jiggle things until the square tables just fall into place. For our current (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) I should point out that at SCLTC, we initially provided spring clamps for temporary connection ($0.99 each) or until bolts were installed, but decided that they really were not necessary. We use wing nuts and just fasten the bolts finger (...) (20 years ago, 13-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Kevin- I agree totally that making tables is -- or can be -- a lot of work. If all we ever did with the tables was set them up at matching heights at a show and then lay LEGO on them, it would definitely NOT be worth it. What does make it (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
Here is what NELUG uses. Most of our tables are 40.25" x 40.25" or 4x4 32x32 baseplates. The extra .25" is to account for the fact that the baseplates are not exactly 10" square but ever so slightly larger. We also use some 40.25" x 20.125". Finally (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
