 | | Hopper car model
|
|
A few months back I designed a (URL) train car: (URL) And recently I built LDraw instructions for it and published them online. What's the best way to share them? I put the CAD file (URL) on my blog> and on Flickr (as a comment under the (URL) 3D (...) (16 years ago, 23-Dec-08, to lugnet.announce.moc, lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Beating up, kicking, and verbally abusing an old dead rotted horse...
|
|
(...) (URL) (16 years ago, 23-Dec-08, to lugnet.trains, lugnet.general)
|
| |
| | Reshaping 4.5v track
|
|
I am wanting to use my old 4.5v tracks for a narrow gauge train that will be 4 studs wide. Obviously the straight track is fine, but it is the curve track that is giving me some bother. Can anyone suggest a solution? (16 years ago, 23-Dec-08, to lugnet.trains)
|
| |
| | What I want for Christmas
|
|
If LEGO granted Christmas wishes, I would have to ask for: 1) 5.5 length technic axle - so my train wheels don't fall off anymore 2) modular train railing system - so I don't have to cut any more hose and the awkward use of minifig hands 3) train (...) (16 years ago, 22-Dec-08, to lugnet.general, lugnet.trains, lugnet.lego.direct, FTX)
|
| |
| | Re: Western Train with instructions
|
|
--snip-- (...) Oh dear. I started to build one and found a fairly big mistake... The front set of big wheels must be replaced by a set of BBB unflanged wheels. The yellow domes must be attached on a top corner, not in the middle. I'll update the (...) (16 years ago, 20-Dec-08, to lugnet.trains, FTX)
|
| |
| | Santa and his Reindeer
|
|
A few years ago I put LEGO train tracks around my son's roof towards the ceiling. This year, I made a team of reindeer and a sleigh to run around the tracks. The Santa is an old LEGO set, but the reindeer and sleigh are MOC. I'm not completely (...) (16 years ago, 19-Dec-08, to lugnet.trains, lugnet.fun.holiday, FTX)
|
| |
| | Seasonal Community Spirit
|
|
Maybe the time of year has something to do with it, but I must confess to have been moved by the generosity of a few talented builders lately. Seperately, we’ve seen (URL) Eric Sophie>, (URL) Tim Gould> and (URL) Mark Neumann> sharing not only their (...) (16 years ago, 16-Dec-08, to lugnet.general, lugnet.inst, lugnet.people, lugnet.trains, lugnet.build.mecha, lugnet.cad, lugnet.western, FTX) !!
|
| |
| | Re: Western Train with instructions
|
|
(...) The final two stages are now up (URL) Loco and tender - (URL) (as (URL)) Passenger - (URL) ((URL)) Lumber- (URL) ((URL)) Boxcar - (URL) ((URL)) Caboose - (URL) ((URL)) Please note I've also resubmitted instructions for the Loco (and boxcar and (...) (16 years ago, 16-Dec-08, to lugnet.trains, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) Ahhh I found them. The original loco and the last two. I must have accidentally switched LPub across to a different setting before doing (and redoing in the case of the loco) the instructions. Newer versions will be uploaded. Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) So do I but going back to the original issue which instructions are using the black edgelines? Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I agree fully with Philo's thoughts about the "Always black" edgelines. cu mikeheide (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I always considered that "Always black" was unusable since dark colors were illegible. So for me the answer is yes. I would be tempted to push the threshold further: even if there is enough contrast on screen, it could be insufficient in (...) (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I agree that dark gray would have worked better for these edge lines. I can easily change "always back" in LDView to be "usually black". I played around with the settings a bit, and with r * 30 + g * 59 + b * 11 <= 3600 as my threshold for (...) (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) See the difference between your instructions and those I created from the MPD: (URL) guess is that your LDView lpub setup has edge lines set to "always black" Philo (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad)
|
| |
| | Re: Western Train with instructions
|
|
(...) Thanks! Strange. The edgelines show up very clearly on my system. I'm curious how other people find them? They're set to something similar to dark grey. Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
Hi Tim, Wonderful models and instructions! (no I'm not turning train ;o)... But I find the edgelines of black parts much too dark, making these parts illegible. What setup did you use? Philo (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Stage III Re: Western Train with instructions
|
|
(...) --snip-- Stage III is up now. (2 URLs) ((URL)). Tim (16 years ago, 16-Dec-08, to lugnet.trains, FTX)
|
| |
| | Qld Rain SMU driver cab
|
|
After messing around for a few months, I gave up and began working on the EMU. Now that I have almost finished the EMU, I have worked out how to do the nose of the SMU. (URL) should be public soon - I hope. (16 years ago, 14-Dec-08, to lugnet.trains)
|
| |
| | Re: Western Train with instructions
|
|
(...) Love that roof design. -Elroy (16 years ago, 13-Dec-08, to lugnet.trains, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) NB. 'finish off 2008' is what I mean --snip-- (...) Stage II is up now. (2 URLs) ((URL)). Tim (16 years ago, 13-Dec-08, to lugnet.trains, FTX)
|
