 | | Re: Bogie design (coupler)
|
|
(...) Ah, suddenly I do understand what you ment here, but unfortunately this would not fit. A 4263 Technic Plate 1 x 4 with Holes under the 2711 Technic Rotor 2 Blade with 2 Studs (with one hole and 2 studs overlap, and only the other hole (...) (21 years ago, 3-Dec-03, to lugnet.trains)
|
| |
| | BBB wheels + availability?
|
|
When?! bm (21 years ago, 3-Dec-03, to lugnet.trains)
|
| |
| | Re: MOC 36 Axle Schnabel Car
|
|
Bruce, is there any way you can post instructions for this? I'd like to take a shot at building one of these and perhaps displaying it at a local train show. -HRH (21 years ago, 3-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Maybe you could lengthen it with part #2905: Technic Triangle, if you don't mind that somewhere inside or under your nose it's sticking out sideways [LDrawPart 2905:7] (...) I have absolutely no clue what you're talking about here, we probably (...) (21 years ago, 2-Dec-03, to lugnet.trains, FTX)
|
| |
| | 4410 "steam engine junction"
|
|
There's a peek at a 2004 train set in the 4408 idea booklet. Sort of. (: -Erik (21 years ago, 2-Dec-03, to lugnet.trains, lugnet.year.2004)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Yep. I actually use this in MTW-1003 because I want the wobble this gives you (it's a bit taller of a pin than a normal bogie plate's pin which fits into two plates worth of space, this is a full brick thick or 2.5 plates) but the flexibility (...) (21 years ago, 1-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
Instead of a bogie plate you can always use a Tile, Modified 2 x 2 with Pin [LDrawPart 2460:0] This gives you more flexibility with how you attache beams etc. you alos don't have to have the pivot poit in the centre of the bogie. Tim (21 years ago, 1-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
Tim David <talltim@hotmail.com> wrote in message news:Hp3116.1Cp@lugnet.com... (...) 1 (...) right (...) between (...) Train (...) stud (...) the (...) 2 (...) that (...) I think it is time that I give my point of view here. I made some tests using (...) (21 years ago, 1-Dec-03, to lugnet.trains)
|
| |
| | Re: Broken Train Motors
|
|
(...) Some silicon grease should do the trick and it doesn't damage the ABS. I use it sometimes on bogie pins with good results. Any decent hardware shop has it. Also, it's almost colorless so it won't look bad. (21 years ago, 30-Nov-03, to lugnet.trains)
|
| |
| | Re: Broken Train Motors
|
|
In lugnet.trains, Reinhard "Ben" Beneke wrote: <snip> (...) One or two of my clips have broken, but always the result of the engine careening off the layout and smashing on the ground. The other clip is still there so I haven't much worried about (...) (21 years ago, 30-Nov-03, to lugnet.trains)
|
