 | | Re: Layout Design Question
|
|
(...) Yes, it does -sort off-. The switch only turns power on/off for the two inside rails. the two outside rails always remain electrically conductive. Since the outside rail goes all the way round, you would create equal polarity on the track that (...) (21 years ago, 18-Jun-03, to lugnet.trains, FTX)
|
| |
| | All Lego Ack Circuit for LDCC
|
|
Hi All, One of the features of the LDCC firmware is the ability to read the configuration variables out of a DCC decoder installed in a train motor. In order to do this, you need to connect a small circuit consisting of one or two resistors from the (...) (21 years ago, 18-Jun-03, to lugnet.trains, lugnet.robotics.rcx)
|
| |
| | Layout Design Question
|
|
I was thinking about setting up my second LEGO switching layout, with this one based on a prototypical track layout which features what amounts to a reverse loop. The loop area serves several industries and the lead into the loop goes to a yard, (...) (21 years ago, 18-Jun-03, to lugnet.trains, FTX)
|
| |
| | Re: Redesigned Intermodal Car
|
|
I (...) I use mostly mutilated pieces of track with a wire soldered onto them for my power connectors. Otherwise, it gets expensive feeding every 40 pieces or so. James P (21 years ago, 18-Jun-03, to lugnet.trains, FTX)
|
| |
| | Inventory for High Speed Train posted
|
|
Thanks to LEGO, we're happy to announce that we just put up the inventory for the new High Speed Train set (4511). See it at (URL) and Jennifer Boger (21 years ago, 18-Jun-03, to lugnet.trains, lugnet.inv) !
|
| |
| | Re: Redesigned Intermodal Car
|
|
(...) And a not too bad one, Stefan..... I have tried that last year on my (URL) renewed turntable> (and yes, there are some further modifications done to the track next to the turntable - in 12V it worked fine without these, because one could (...) (21 years ago, 17-Jun-03, to lugnet.trains, FTX)
|
| |
| | Re: Redesigned Intermodal Car
|
|
(...) What about soldering the leads to the rail? That way they wouldn't come off. The heat would be the only concern, though I don't think it would damage it alot. Just an idea. -Stefan- (21 years ago, 17-Jun-03, to lugnet.trains, FTX)
|
| |
| | Re: Redesigned Intermodal Car
|
|
(...) Gasp! Without consulting Conan first??? (the electrical guy). Hey, keep me posted as to what you find-- it sounds like a good idea. I will be having my leads in some mountain, so nobody would see the, err, mutilation anyway:-) (...) That why I (...) (21 years ago, 17-Jun-03, to lugnet.trains, FTX)
|
| |
| | Re: Redesigned Intermodal Car
|
|
(...) Four? I count five, and that's not counting the one I have for my Husky Stack...:-) (...) Thanks for the props, Stefan! The trucks are my son's design. JOHN (...) (21 years ago, 17-Jun-03, to lugnet.trains, FTX)
|
| |
| | Re: Redesigned Intermodal Car
|
|
(...) Have you tried not using the power leads at all? I haven't tried it, but it would seem that if you cut a 'normal' 9volt wire, split the end and strip a short section of wire -- you could pry up the metal part of a rail enough to slip the wire (...) (21 years ago, 17-Jun-03, to lugnet.trains, FTX)
|
