 | | Re: Super Chief set not ready for prime-time
|
|
(...) I agree with that! And I bought all of the newer cars (10013/14/15/16/17) and buy just making a very simple train with them + 1 loc, it has a very hard time on curves and not fast on a straight track. I never had that problem with all the (...) (22 years ago, 16-Oct-02, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
I have two Santa Fe engines and a B Unit I built to go with them. I have two moters one on each of the A units. I too had a hard time with the SF engines pulling more then 10 cars. It always seemed to bog down in the turns. Recently I had all my (...) (22 years ago, 16-Oct-02, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
When you say you replaced the wheels, are you referring to the whole kit 'n caboodle or just the axle? -Stefan- (...) (22 years ago, 16-Oct-02, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
I ment that I called up LEGO and they sent me a whole new set of wheels. THey had no problem with it. After replacing the old SF wheels with the new, I looked at what would cause the high friction. It looks like the outer most diamater of the wheel (...) (22 years ago, 16-Oct-02, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
Yup. Thanks. -Stefan- (...) (22 years ago, 17-Oct-02, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) That's it in a nutshell. I bought some SF carriages and Super Chief and after running them for only a short amount of time it slowed right down. The Motor was cutting out due to the load, from the weight of these heavier carriages. Not the (...) (19 years ago, 10-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) (URL) (19 years ago, 11-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) wonder? Way better solution than knifing away plastic if it works... ++Lar (19 years ago, 12-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) Hi all! This is in fact a nice idea! But I have one comment to make: this solution is causing friction between brass tube and metal axle, while the original solution is "rubbing" only on the very tip of the metal axle. The higher the diameter (...) (19 years ago, 12-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
A slightly better solution may be to find similar stock in the pre-lubricated bronze used for bushings. I don't know the true name of the stuff, but if tubing of the right size could be found, you wouldn't need to worry about grease or oil. (...) (19 years ago, 15-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) Umm yeah, well I think you missed the point, NO lube is needed In lugnet.trains, Peter Edwards wrote: (...) (19 years ago, 16-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
Cool, missed that part. Now...details on the sizing, where to buy, etc? I'm sure I could bore out some brass rod, but if you have a supplier that stocks the right size, it would save a ton of time... (...) (19 years ago, 16-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) I picked up 300mm x 3mm rod just in a local hobby shop (URL) (19 years ago, 21-Mar-06, to lugnet.trains, lugnet.lego.direct)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
(...) (URL) Brick Blast Vermont>. This was are first experiance doing a mid summer train show and it was extremely hot and humid durring the event. My trains which have been running at shows for 7+ years would not run at all because of the friction (...) (18 years ago, 3-Aug-06, to lugnet.trains, lugnet.lego.direct, FTX)
|
| |
| | Re: Super Chief set not ready for prime-time
|
|
I tried this solution out for myself, and it didn't produce the best results for rolling friction. Not to say it isn't a good solution, because I do see major improvements, but just that there is a better one. Adding the metal sleeve around the (...) (18 years ago, 5-Aug-06, to lugnet.trains, lugnet.lego.direct, FTX)
|
