 | | Re: Caboose in service!
|
|
Down here on CSX we still use cabeese as shoving platforms. Of course everything is stripped out of them except a couple seats...for those rough shoving moves. -Harvey (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Real Life Amtrak LEGOLAND train car advert
|
|
(...) So I asked LLC about this, and it was part of a promotion that ran sometime back. I am trying to get ahold of some additional photos and info. If I can, I will post them to the www.LEGO.com/trains site. Info to follow. Jake -- Sr. Producer (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Caboose in service!
|
|
"Christopher Masi" <cjmasi@*nogarbagepl...e*rcn.com> wrote in message news:cjmasi-CC261A.2...net.com... (...) [ ... snipped ... ] About two weeks ago I was on my way to Denver via Chicago from Raleigh. As my RDU-ORD flight was landing I noticed a (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Ogel's Train of Assimilation
|
|
(...) Thanks, I wish I could participate more (at all?) in the SCLTC, but it requires significantly more time than LUGOLA does. I don't have much time with our baby to tend. (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Ogel's Train of Assimilation
|
|
(...) Thanks - I've proposed a meeting for September 7th so let's hope that becomes a reality! (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Ogel's Train of Assimilation
|
|
(...) Thanks - I had a lot of trouble engineering that front section. It is constructed as follows: A 1x4 brick with studs on the side A 1x2 hinge piece attached to the side studs of the first brick A 2x2 round-table plate attached to the hinge The (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Caboose in service!
|
|
Hey all, I saw a caboose in service the other day. A GP-something or other (sorry I am such a bad/lazy rail spotter) was pulling a caboose and three box cars. The caboose was tucked in between the engine and the box cars. GP-{caboose}-{box car}-{box (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: GP40 dat file
|
|
(...) While it is not exactly a GP40, it is quite similar: (URL) version built on plates rather than standard LEGO Train baseplate) If you are interested, I can send you the .ldr for either one. Jake --- Jake McKee LEGO Enthusiast Webmaster - BI (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: GP40 dat file
|
|
(...) My engines are a little bigger than standard :) but I have a dat file of my SD40-2 that I made using MLCAD[1] a while ago (URL) recently while lying on my back for four days due to a back injury[2] I completed directions for my CP30. I made (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
| |
| | Re: Is 12v compatible with 9v???
|
|
(...) Yes and no. You have to file down some plastic on the inside of the 12v electrified rails to get them to snap onto the 9v tracks. Also, the wheels on the 12v trains knock against the 9v power supply bricks, and can eventually knock the 9v (...) (22 years ago, 15-Aug-02, to lugnet.trains)
|
