 | | Re: Point Motor Instructions
|
|
Jason J. Railton wrote in message ... (...) point (...) and (...) You can also prevent this by using one of those white Technic 'Tooth Clutch' / reduction gears as I did here: (URL) I realise that this setup needs some perfectioning (anyone? feel (...) (23 years ago, 31-Jan-02, to lugnet.trains)
|
| |
| | Re: Brickmania goes to Brickswest!
|
|
(...) Cool, Dan, I wish I could be there! But you should've probably posted this to lugnet.events.brickswest (follow-ups set there) Regards ROSCO (23 years ago, 31-Jan-02, to lugnet.castle, lugnet.build.arch, lugnet.build.military, lugnet.trains, lugnet.events.brickswest)
|
| |
| | Re: New Waggon in 7-wide / plus combine harvester /seven wide mania continues
|
|
(...) load. (...) Dear Mattias, thanks once more for your kind words! But the power of the BR50 is not so huge since it has only one 9V motor in the tender. In fact its power is quite limited since this motor has to drive 8 further axles inside the (...) (23 years ago, 31-Jan-02, to lugnet.trains)
|
| |
| | Still not ready???, was (Re: Trainposter almost ready!)
|
|
I was looking closely at the latest Train Poster and think there are still two models missing. The flatbed from the 4553 Train Wash & the container flatbed from the 4555 Freight Loading Station. Maybe I miss this discussion? SteveB (...) (23 years ago, 30-Jan-02, to lugnet.trains, lugnet.cad)
|
| |
| | Re: New Waggon in 7-wide / plus combine harvester
|
|
(...) Good work again Ben! Your impressive Br50 really deserves a number of cars to haul so it can show its true power. I must say you have chosen an original subject for the load on the flat car. Do you have a special relation to this harvester? A (...) (23 years ago, 30-Jan-02, to lugnet.trains)
|
| |
| | Re: Remote Turnouts and Decouplers
|
|
(...) You need to have two power wires. The first wire connects to the motor in the switch house and to the polarity switch, either end of the switch is ok. The second wire connects to the power source and to the other end of the switch. Turn your (...) (23 years ago, 30-Jan-02, to lugnet.trains)
|
| |
| | Brickmania goes to Brickswest!
|
|
Hello everyone! This is an announcement to anyone concerned that I am travelling out to Brickswest next month to take part in activities there. Here is the official description of the workshop I am hosting: "Daniel Siskind, owner of Brickmania (...) (23 years ago, 30-Jan-02, to lugnet.castle, lugnet.build.arch, lugnet.build.military, lugnet.trains) !
|
| |
| | New Waggon in 7-wide / plus combine harvester
|
|
Hi all, I just wanted to announce a small new MOC of mine. For my recently built BR50 steam engine I have now finished the first freight waggon in fitting size. It's a 7-wide flat car in dark grey with a combine harvester oldtimer as load. You may (...) (23 years ago, 30-Jan-02, to lugnet.announce.moc, lugnet.trains) !
|
| |
| | Re: Remote Turnouts and Decouplers
|
|
Steve & All, (...) All right, thanks for the hard work! Now, let me see if I get this: 1) Modify the switch as stated above. 2) Build the switchhouse as stated above. Where does that polarity switch come into play? I have little experience with (...) (23 years ago, 30-Jan-02, to lugnet.trains)
|
| |
| | Re: Vintage train part identification
|
|
(...) should've mentioned this too... in Parts Ref. (URL) (23 years ago, 30-Jan-02, to lugnet.trains, lugnet.fabuland)
|
