 | | Re: Proposed 'Legomodule' standard
|
|
(...) This is fine. Have you considered...lowering the scenery and keeping the track at the same level? However, I would tend to think that it would work either way...and 10 bricks high is buildable by more people than 20 (about 2/3 bricks as a (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Proposed 'Legomodule' standard
|
|
Larry P and I have been overloading my email server going back and forth on this topic today. This is what I'm proposing: TWO standards. A 'LOW' standard, and a 'HIGH' standard. Low standard is 10 bricks tall, High standard is 20 bricks tall. We'd (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Re: Lego Modular tables
|
|
Good start. I've found the locations of set track alignments to be a tricky one. Since LEGO track doesn't (yet) come in differnent lengths, does your proposed standard presume the track ends right at the end of the module, or perhaps 8 studs from (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Re: Building my train table
|
|
Mike has some good points. The PNLTC design isn't the most simple thing out there and Mike suggested a reasonable alternative. The PNLTC design is designed to keep weight to a minimum and still have sufficient strength. Personaly, I have 8 or so of (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Lego Modular tables
|
|
Why not do this in the mannor of N-track? Lenghts in multiples of 2 sections of track. Width: any width Ends: Track centers to be located at: 10 studs in, 20 studs in, (30 studs optional) from front of table. Hight: To be 36" or 40" high. Now, some (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Re: Minifig What scale are they??
|
|
Ahh, the ageless question :) Dave Eaton and I, in the course of our AT-AT Marathon (I'm still recovering ...) e-mailed each other regularly on issues about scale. For the most part, I went by the minifig's height, and said that it was equal to 1.8 (...) (25 years ago, 23-Mar-00, to lugnet.build, lugnet.general, lugnet.trains, lugnet.town)
|
| |
| | Re: Building my train table
|
|
(...) For a schematic of the current iteration of the GMLTC layout, check out: (URL) The dimensions of the rectangles are 30" x 45" (6 large gray baseplates) -John (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Re: Building my train table
|
|
2. Get some Birch faced plywood. It has a closed grain that will take primer and paint well, or if that is too expensive, just get some plain old plywood. Make sure to use primer if you use the plain stuff, so that the grain will be hidden. Build (...) (25 years ago, 23-Mar-00, to lugnet.trains)
|
| |
| | Re: Minifig What scale are they??
|
|
(...) You've never seen S4 then...since it had NO tolerances except those that were scaled from full size. (and it was not one person who built to it, there were a bunch of people who built to it). In larger "scales", I beleve the work of Leo Myers (...) (25 years ago, 23-Mar-00, to lugnet.build, lugnet.general, lugnet.trains, lugnet.town)
|
| |
| | Re: New LEGO train realism?
|
|
"Dean Husby" <nntp@akasa.bc.ca> wrote in message news:38D99A3F.9ED3C5...a.bc.ca... [ ... snipped ... ] (...) leaning (...) maximum (...) several reasons. 1) We didn't see any reason to re-invent the wheel - I am personally not a big NIH fan. 2) We (...) (25 years ago, 23-Mar-00, to lugnet.trains, lugnet.trains.org)
|
