 | | Re: Color me surprised...
|
|
(...) Superb, you see what a little bit of trans-atlantic team-work can yield. (...) Agree, I think this sunny snapshot shows the BNSF Heritage 1 scheme rather nicely: (URL) With friendly greetings, M. Moolhuysen. (20 years ago, 6-Jul-04, to lugnet.events.1000steine-land, lugnet.lego, lugnet.trains, FTX)
|
| |
| | New, Modern BNSF Loco From TLC? (Re: Color me surprised...)
|
|
(...) Of course you are correct! (the part about James remains to be seen). Also, an "SD" might be questionable, because of the added complication of adding the extra axle, so I would guess a "GP". But you never know.... I didn't quite understand (...) (20 years ago, 6-Jul-04, to lugnet.events.1000steine-land, lugnet.lego, lugnet.trains, FTX)
|
| |
| | NGLTC club house open house event pictures
|
|
The North Georgia LEGO Train Club (NGLTC) held it’s first of three open houses at it’s Discover Mills Club house on June 26th. It was a very busy day at the mall thus making for a good crowd at the open house. Here are a few pictures from the event: (...) (20 years ago, 6-Jul-04, to lugnet.trains, lugnet.trains.org, lugnet.general)
|
| |
| | Re: Color me surprised...
|
|
(...) or something. Mr. Mathis hasn't been saying much lately... (URL) and look at the Heritage 1 scheme. There are better pics out there... (...) Ditto. Dark green is a sweet color. (...) (20 years ago, 6-Jul-04, to lugnet.events.1000steine-land, lugnet.lego, lugnet.trains)
|
| |
| | Re: 8 wide help needed
|
|
(...) Yes;-) It really depends upon what you want to build. I have employed all three ideas: (URL) Here> is an example of using a 6 wide train baseplate (you can just see a hint of the gray baseplate). (URL) Here> I used basically just 6x8 plates. (...) (20 years ago, 6-Jul-04, to lugnet.trains, FTX)
|
| |
| | One week left - more pics from BayLTC Pleasanton Show
|
|
Since June 12, the Bay Area LEGO Train Club (BayLTC) has had a layout on display at the Amador-Livermore Valley Historical Society and Museum in Pleasanton, California. There is one week left until we take it down next weekend on July 11. This (...) (20 years ago, 5-Jul-04, to lugnet.announce, lugnet.trains, lugnet.org.us.baylug, lugnet.loc.us.ca.sf, FTX)
|
| |
| | Re: 8 wide help needed
|
|
(...) I custom build my baseplates using regular plate, 3 layers thick with 2x4 technic plates built in to accept the bogie pin. I place the technic plate length wise on one layer and sideways on the other. I find the 6x train bases too resticting (...) (20 years ago, 5-Jul-04, to lugnet.trains)
|
| |
| | Re: 8 wide help needed
|
|
(...) For short trucks with four wheels I use a standard 6x24 baseplate with 2xn plates along the edges (see brakevans from the link below) and make the single pairs of wheels rotate a bit with small belts to pull them back to straight. This is (...) (20 years ago, 4-Jul-04, to lugnet.trains)
|
| |
| | RichLUG and HardLUG to Display at GATS - July 17 & 18
|
|
The Richmond Lego Users Group (RichLUG) and Hampton Roads Lego Users Group (HardLUG) will present a join display at the GATS show in Richmond, Virginia, on July 17 and 18. The Showplace exhibition center, located at 3000 Mechanicsville Turnpike) (...) (20 years ago, 4-Jul-04, to lugnet.org.us.richlug, lugnet.trains.org)
|
| |
| | Re: 8 wide help needed
|
|
(...) Hello Adam , There are a few ways ,it can be done! If you are building no longer than 28 studs. Then use a 6 wide train base and put 2 wide plates on the edges of it. That would be the easiest way. I have used a 6 wide train base in my 8 wide (...) (20 years ago, 4-Jul-04, to lugnet.trains)
|
