|
|
 | | Re: Building Fences
|
| Duane Hess wrote in message ... (...) the (...) though.... Well if you don't really care about being able to see through the fence, I use 1x1 bricks with 1x1 plate with clip horizontal stacked on top, 2 pairs high, then technic straws (flex system (...) (23 years ago, 14-Nov-01, to lugnet.town)
| | | | | Re: Building Fences
|
| (...) <snip> (...) Ooooh.. that's nice. I could see using that as a gated entrance, but I don't have any of the grate pieces. Drat. (...) I'm actually thinking about cheating in a large way. I was contemplating using 1x1 bricks stacked about 6 high (...) (23 years ago, 14-Nov-01, to lugnet.town)
| | | | | Re: Building Fences
|
| (...) Although your problem calls for a slightly different solution then what I have to offer, here is an mockup for a heavy duty fence that I am building for my current project. The final fence will only cover a single baseplate but will be a (...) (23 years ago, 14-Nov-01, to lugnet.town)
| | | | | Re: Building Fences
|
| I don't know if there IS an economical way, as you are generally going to want to put vertical plates in place, and just about any part necessary to do that isn't that economical on a grand scale. You could use 1x1 headlight bricks, or technic (...) (23 years ago, 14-Nov-01, to lugnet.town)
| | | | | Building Fences
|
| I'm working on an assembly yard (too big for a single building, I've already tried) for a vehicle that is under construction. The area is a minimum of 3 x 4 baseplates, it may grow later. I would like to build a fence around it to keep all of the (...) (23 years ago, 14-Nov-01, to lugnet.town, lugnet.trains)
| | | | | Re: Engine 71 - New Fire Truck
|
| (...) the (...) at (...) them. Sounds great, although with the flex tube ladder all you need are a couple of 1x1 plates with clips and you're sorted ;-) Jennifer (23 years ago, 14-Nov-01, to lugnet.general, lugnet.build, lugnet.town)
| | | | | Re: Engine 71 - New Fire Truck
|
| (...) pre-minifig Lego style (the cab of the truck) with more modern Lugnetesque design ideas (the details on the rear). Also, I especially like your control panel which uses the Technic bricks with the short pegs to simulate knobs, gauges, and hose (...) (23 years ago, 14-Nov-01, to lugnet.general, lugnet.build, lugnet.town)
| | | | | Re: Engine 71 - New Fire Truck
|
| (...) went with the 1x16 beams because of how the ladder hangs off the side of the truck. Basically there are two 1x2 hinge bricks set into the side of the truck, at the level of the top of the back wheel. Attached to each hinge brick is a 1x2 plate (...) (23 years ago, 14-Nov-01, to lugnet.general, lugnet.build, lugnet.town)
| | | | | Re: Pics of VLC layout at Trains 2001 show, Burnaby BC
|
| (...) The 'Popular Vote' was not handled well this year. There was NOT one announcement about it, everyone I talked to said "What a popular vote? Where do I do it? How?" etc... So most didn't vote I'd bet... Since no one but the regular train people (...) (23 years ago, 13-Nov-01, to lugnet.trains, lugnet.town, lugnet.org.ca.vlc, lugnet.loc.ca.bc.van, lugnet.loc.ca.bc.vic)
| | | | | Re: Pics of VLC layout at Trains 2001 show, Burnaby BC
|
| (...) Here's a pic of my wife holding the plaque last year... (URL) Dean Husby LUGNET Member #320 TFM's LEGO Workshop - (URL) Vancouver LEGO Club - (URL) (23 years ago, 13-Nov-01, to lugnet.trains, lugnet.town, lugnet.org.ca.vlc, lugnet.loc.ca.bc.van, lugnet.loc.ca.bc.vic)
|
|
