 | | Re: Suspension
|
|
(...) Your approach is certainly very interesting! Honestly, I didn't know what a DeDion axle was, but I do now. :-) The design is probably very efficient and low frictiony, like you say. And keeping the differential fixed makes the rest of the (...) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: Suspension
|
|
(...) Ah, yes! A custom made independent suspension, much like the one on 8448 or 8865. This approach will need no less than four universal joints. I think that it prevents the width of the vehicle from being narrow, so I've never used this approach (...) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: Suspension
|
|
Update on the rover: The rear end is complete, including the articulating section which is driven by a micromotor. I tested it by adding a couple big wheels to the front, and as long as the vehicle is moving forward, it turns quite nicely, thanks to (...) (25 years ago, 12-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: LEGO Service, questions.
|
|
I don't know about all pneumatics, but I know that the 5099 pneumatic switches are still available here in Sweden; I just ordered a lot of them. Service packs in Sweden are quite expensive, but at least their selection seems very good. Sweden gets (...) (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: Suspension
|
|
(...) I'm a bit of a Johnny come lately in this thread, but I did attempt something similar to this a wee while ago. The idea was to build a 6 wheel drive Moxy style articulated dump truck, the chassis for which sounds not dissimilar to your (...) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Wheels
|
|
I need two large grey wheels as from set 8860. I am willing to trade with wheels the same size but in white. Anyone ? In the UK preferably. Michael Pratt (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: Suspension
|
|
Hmmm, sounds like the menu with hover buttons is causing some problems. Try this direct link to the page. You won't get the menu frame to the left or the title frame to the top, but you'll be able to see the important stuff! You should be able to (...) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: RC control on Pneumatics, gearboxes and polarity switches
|
|
Ok, I got the pics uploaded, the address is (URL) it out and see what you think. Adam Ogle Adam Ogle wrote in message ... (...) control, (...) more (...) (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: Suspension
|
|
(...) Loads fine in NS 4.73, but when I try to close the window, it crashes NS all together. --Karim (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: LEGO Service, questions.
|
|
(...) Lucky me I'm in Sweden then :P When I spoke to 'em this week thay had everything I wanted in stock :) /Tobbe - (URL) (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: LEGO Service, questions.
|
|
(...) or as John helpfully said: (URL) numbers 63, 64, and 65 should be the spareparts catalogue. /Tobbe (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: Suspension
|
|
(...) Works fine in my 4.72 Netscape. /Tobbe - (URL) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: New Hexapod
|
|
(...) Well that’s what I call great engineering! Ever thought of drawing the hexapod in LDRAW? I’ll hope to finish my drawing this weekend so I can publish it. It is a hexapod with three motors, MS and all is 18 studs long and 10 wide. Then see my (...) (25 years ago, 11-Aug-00, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Super Truck
|
|
(...) thanx... but it wasn't that hard. It took me about a day.. to build,rebuild...,reb...ld,rebuild and rebuild I had just one problem.... , look at the picture partsleft.jpg I was ill and had to stay in bed for a week so that's boring.... That is (...) (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | Re: Super Truck
|
|
(...) Great job. I don't have the set but I don't think I could make it into such a great truck. -Nick (25 years ago, 11-Aug-00, to lugnet.technic)
|
| |
| | New Hexapod
|
|
hello boys and girls this is a technic hexapod i actually finished a while ago but never got around to publishing. it runs on one motor and is no longer than a single technic beam. check it out and let me know what you think.... (URL) (25 years ago, 10-Aug-00, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Suspension
|
|
(...) I attached the wheels to the motor, and built most of the rear engine compartment, including exterior body and fiber-optic engine. The suspension is quite stiff. Thanks to a worm gear, the vehicle moves slowly but steadily. The fact that the (...) (25 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| |
| | Re: code pilot program 8479 New??!!
|
|
(...) I found it shortly after getting me "Green truck" (What a wonderfull colour that is by the way) I was hoping that it would let me construct my own sequences, and the combine them into a single barcode, but nono, it simply prints all the codes (...) (25 years ago, 10-Aug-00, to lugnet.technic)
|
| |
| | Re: code pilot program 8479 New??!!
|
|
I've had it for at least a year. It could be older and there may be a newer version now. My complaints were that it was rather limited in the "length" of a program allowed, even though the CodePilot will store the bigger programs. And I believe the (...) (25 years ago, 10-Aug-00, to lugnet.technic)
|
| |
| | RE: Suspension
|
|
(...) I hope it works :) I've built two wheels with suspension now, so I'll try to get it motorized and then add the rest of the frame, the articulation, and the other wheels. (...) I'm not ;) Instead I built a somewhat similar system: basically two (...) (25 years ago, 10-Aug-00, to lugnet.technic, lugnet.build)
|
