 | | 2007 sets: Huge RC Bulldozer and Combine Harvester
|
|
8274 Combine Harvester (URL) RC Bulldozer (URL) (18 years ago, 6-Jan-07, to lugnet.technic) !
|
| |
| | Re: Mindstorms fabrication/manufacturing line...
|
|
(...) That machine is ingenious. I like the way he has his RCX bricks communicating by traveling along with the assembly line. I also like the frame he made to hold the wheels while the body was pushed onto them. Brilliant. (...) This reply is (...) (18 years ago, 5-Jan-07, to lugnet.org.ca.rtltoronto, lugnet.robotics, lugnet.robotics.rcx, lugnet.technic)
|
| |
| | Re: What's the difference?
|
|
(...) Yes, and keep in mind that the advantage with an 18speed transmission that I described in my last post,is that you could go through your low gears without splitting them, flick into high range and split whichever gears you want...gives you (...) (18 years ago, 23-Dec-06, to lugnet.technic)
|
| |
| | Re: How to use this part to flip something?
|
|
(...) I realized in this picture, you can see a little more of the part in the lower left of this image. (URL) Since the part is at the core of the joint, it is hard to see it. You can see where the joint pivots, that is where the pivot point of the (...) (18 years ago, 23-Dec-06, to lugnet.technic, FTX)
|
| |
| | Re: How to use this part to flip something?
|
|
"Eric Sophie" <mylegomaster@aol.com> wrote in message news:JApuop.Jny@lugnet.com... (...) That's an awesome model there! Any chance you can show how you used the part in a separate image? (...) I see. Well, almost! ;-) But that's a load of eye (...) (18 years ago, 23-Dec-06, to lugnet.technic)
|
| |
| | Re: How to use this part to flip something?
|
|
(...) I used that part to act as the fulcrum and geared lever for the suspension on my (URL) Blue Quad>. (URL) (...) I used the part to create an shock absorb/dampen system, because the part is also used as a fulcrum, the shock returns it to (...) (18 years ago, 23-Dec-06, to lugnet.technic, FTX)
|
| |
| | How to use this part to flip something?
|
|
(URL) been looking at this part, Technic, Arm 2 x 5 with 1/4 Gear 8 Tooth Double Bevel, and I figure it should be simple enough to use it to flip something to one side, but I'd like to know if anyone has tried doing this in a Technic creation of (...) (18 years ago, 23-Dec-06, to lugnet.technic)
|
| |
| | New Quad - Quadra Mech .3
|
|
(6 URLs) enjoy. (URL) (18 years ago, 23-Dec-06, to lugnet.announce.moc, lugnet.technic, lugnet.space, lugnet.build.mecha, FTX) !
|
| |
| | Re: What's the difference?
|
|
(...) Yeah I suppose it would be, because you would have two different sets of gears that could both be changed. So in that way they'd be the same. The trick is to not duplicate ratio's because that's a waste. (18 years ago, 22-Dec-06, to lugnet.technic)
|
| |
| | Re: What's the difference?
|
|
(...) Is it something like the front and rear sprockets of a 10+ speed bike? I know there are frequently duplications of gear ratios there. (18 years ago, 22-Dec-06, to lugnet.technic)
|
