 | | Re: Lego pneumatic systems overview?
|
|
(...) I'm not sure and my bricks aren't around as I type this; Does the 1 x 1 technic brick [1] (or similar) slide over the hose end when it's connected? If so that should make a real snug fit for the hose. Perhaps some other brick can do this (...) (21 years ago, 26-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
Tobbe Arnesson wrote: > The hoses will pop-off before any damage is done due to preassure. The preassure > will also leak out in time so there's no danger there either. I verified this for myself tonight with three pumps working three airtanks and (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) The four bar linkages used for driving excavator buckets are good for doing appoximately 180 degrees motion, especially when you have to go "round a corner". The following shows an example - I'm not sure about its angular range but certainly (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) Levers are your friend! Have a look at the mechanisms used to drive the buckets on 8455 backhoe (front and back), and similar models. While these operate nowhere near 180 deg, adjustment of lengths/fulcrums may well get you closer. ROSCO (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) Near 180 degrees maybe tough. You'll need to keep the piston attached as close as possible to the pivot point of the arm to get the maximum range. <snip> (...) Thanks for the positive feedback. I have three large pumps all attached to the same (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) What I'm currently thinking about is a mechanisim that will move an arm that's hinged at one end through a near 180 degree arc before it comes to a rest and then to have the reverse switch pull the arm back to it's initial position. At one end (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) That's good news. My interest is in building full-built models and not the technic see-through style efforts that I usually see the pneumatics used on so it'll be important that the cylinders are capable of moving the combined weight of the (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) Thanks for the heads up, that presentation really does help out quite a bit and the outlet plug is also a good idea. I'm awfully surprised that there is no official outlet cap after all these years, but I suppose that Lego never felt one was (...) (21 years ago, 25-Sep-03, to lugnet.technic)
|
| |
| | Re: Shocking news from Brickset
|
|
(...) My speculation #3 has come true!! (URL) from S@H> when told to ship to Canada: Item#: 8438 Ages: 11+ Pieces: 839 Price: USD 84.99 Preorder this item today, will ship by 24 Oct 2003 Hooray! Even though I already have a 8431. The Backhoe is on (...) (21 years ago, 25-Sep-03, to lugnet.technic, FTX)
|
| |
| | Re: Lego pneumatic systems overview?
|
|
(...) My friend Doug has used them up to 30 PSI. (...) I don't know what the maximum allowable pressure is, but 30 PSI is probably a good upper bound. It depends on which direction you are trying to move the weight. If you are trying to move it (...) (21 years ago, 23-Sep-03, to lugnet.org.us.lugola, lugnet.technic)
|
