 | | Re: new 2003 sets: 8455
|
|
"Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:H9xI82.E49@lugnet.com... (...) i know it would not to keep the line of lego elements but maybe new pistons have one half of hole as pin and the second half as alxe hole it would solve much, (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
"Eric Sophie" <mylegomaster@aol.com> wrote in message news:H9wyr6.9qz@lugnet.com... (...) looks like lego want to be sure that nobody will build really flying machine cause all other propellor have a pin hole instead axle hole :( so we are probably (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: new 2003 sets: 8455
|
|
(...) What I meant as impossible is the two solutions found abouve since you no longer can attach studs on the bottom of the piston. I'm sure the pistons still can be attached back-to-back in another manner, hence more difiicult. But who knows? (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
Question: Since I don't know what the z24 exactly looks like on the prop, is it just like the regular gear? Reason I say, I'm curious, because you could use the holes on the gear to pin another z24 to it and then you'd have a place to mount another (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
(...) What about attaching another 24t along the same axis with a friction pin, then having an axle in that? You'd probably need to drive both to stop rotation at the friction pin. ROSCO (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
You inspired me to tinker a bit, but I am still unsuccessful. Putting gears around the z24 to help stabilize it is problematic because, at standard LEGO distances, there is sufficient space between the gears to allow the z24 (and the prop axle) to (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
(...) I agree, it even causes a problem when used in the actual set! IMO this is one of the worst LEGO parts ever. ROSCO (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
Ho Mark, This presents a significant problem. I always engineer my gear-trains to include a double "axle grab" on both sides of a gear so the gears flow smoothly. Without that extra stud worth to help anchor the Airscrew, yep could be a problem. But (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
I have this part (from <set:8855>) and I have been unsuccessful in my attempts to power it to any significant speed. The problem is that the prop and z24 gear are permanently molded to a 3L axle which goes through a 1x4 Technic beam. Having only one (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
| |
| | Re: Props for Hovercraft
|
|
Tobbe, ya only one set and service pack ever. :( I don't have one either. I know of serveral ways to get some high RPM gear configs. Looking at the Airscrew I be it can push a good volume of air. As Pixel said the trick is creating a good duct to (...) (22 years ago, 7-Feb-03, to lugnet.technic)
|
