 | | Re: legOS —Dave Baum
|
| | | (...) If you're using a Scout then you need to add the -Tscout option... nqc -Tscout -d test.nqc Unless you are using NQC 2.3 b1, you'll need to manually set the Scout in "power mode" before trying to download. (version 2.3 b1 will do this (...) (24 years ago, 14-Feb-01, to lugnet.robotics.scout)
|
| | | |
| | | | | Re: legOS —Alex Fort
|
| | | | (...) Thanks I got the test.nqc flie to download and it worked....but when I try any program from the unoffical guide to lego mindstorms robots like the Hank The Bumper Tank program, it gives me the undifined variable error it says "undifined (...) (24 years ago, 14-Feb-01, to lugnet.robotics.scout)
|
| | | | |
| | | | | | Re: legOS —Dean Husby
|
| | | | | (...) As far as sensors go for the SCOUT you DO NOT have to declare them at all. Just comment out anything to do with declaring Sensors. The scout uses a different command to get the RAW values. For the Scout the the sensors are always TOUCH. Hope (...) (24 years ago, 14-Feb-01, to lugnet.robotics.scout)
|
| | | | | |
| | | | | | | Re: legOS —Alex Fort
|
| | | | | | (...) Just (...) Thank I figured out how to use the sensors I must have an old version or somthing because i have to write the "#ifdef"decleration and the "#endif" decleration on top and on the bottom of the "SetSensor(SENSOR_1, SENSOR_TOUCH);" here (...) (24 years ago, 15-Feb-01, to lugnet.robotics.scout)
|
| | | | | | |
| | | | | | | | Re: legOS —Alex Fort
|
| | | | | | Sorry my E-mail address is neo@fortworks.com Alex (24 years ago, 15-Feb-01, to lugnet.robotics.scout)
|
| | | | | | |
| | | | | | Re: legOS —Dave Baum
|
| | | | (...) Most of the programs out there are for the RCX, not the Scout. Where possible, the APIs are the same between the two, but there are a lot of unavoidable problems. For example, the RCX has configurable sensor ports, so the program must make (...) (24 years ago, 15-Feb-01, to lugnet.robotics.scout)
|
| | | | |
| | | | | | Re: legOS —Alex Fort
|
| | | | | (...) How would you use the built in light sensor like this? "SetSensor(SENSOR_3,...R_LIGHT);" or somting like that? Oh and can you use the temprature sensor on the scout? Alex (24 years ago, 15-Feb-01, to lugnet.robotics.scout)
|
| | | | | |
| | | | | | | Re: legOS —Dave Baum
|
| | | | | | (...) SetSensor() doesn't work at all on the Scout. By definition, SENSOR_3 is the light sensor and configured in a somewhat unusual mode (it reads 0, 1, or 2). Its been a long time since I've worked on the Scout. I think you set the light (...) (24 years ago, 16-Feb-01, to lugnet.robotics.scout)
|
| | | | | | |
| | | | | | Re: legOS —Dean Husby
|
| | | | (...) Dave, doesn't NQC support the 3rd motor port as the light? I would assume that the speed would just be ignored? At least that's what the Lego Remote does... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 5-Apr-01, to lugnet.robotics.scout)
|
| | | | |
