 | | Re: Error in program
|
|
Well I am just a newbie to NQC and to the whole Mindstorm experience, however here is what the compiler says when I try to compile the program that you submitted. Line 1: Error: RCX does not support Arrays I hope that this helps. Chris (...) (24 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Wake On IR -- is it possible????
|
|
All, I was wondering if there is anyway to put the RCX into basically a stand-by power saving mode and have it wake up when sent a command through the IR, basically "Wake on IR". That would be real handy for my Lego Cam when I want to turn on the (...) (24 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) Thank you Frank, I had forgotten about that. Thank you for bringing it up. This info will save considerable suffering in future! Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 31-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Error in program
|
|
Hi, can somebody tell me why this little program doesn't give any output? It just keeps running and doing nothing... int Edges[7], CounterLength=0; task main(){ SetSensor (SENSOR_2, SENSOR_TOUCH); until(CounterLength == 8){ Edges[CounterLength] = (...) (24 years ago, 31-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) program (...) Dean, you are right and meanwhile I could test it. However, the definition for the global variables must be in the SAME ORDER order for both of the programs. If you would do this: SLOT 1: int testvar1 = 1; int testvar2 = 2; int (...) (24 years ago, 31-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Power Down for RCX
|
|
(...) There are two commands (available on the command line or within a program). The first sets the "sleep time", which is the number of minutes before the RCX will turn itself off (0 means never sleep). The second requests that the RCX sleep (...) (24 years ago, 31-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) Your example did as I have stated. Global variables are global across all program slots. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 30-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) Dean, I am not sure that this is correct what you write about global variables. As far as I know, the followoing is correct: - 32 global variables are only valid WITHIN one program slot. - Within this slot, all tasks, functions and subroutines (...) (24 years ago, 30-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) Yes. To be more precise I believe it's 6100 bytes of space. (The SCOUT has 400 bytes of space) (...) if message = 5 then jump off table... It's that easy... (...) Well if you can keep all the code in one program it's easier. But you get 32 (...) (24 years ago, 29-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Just some really basic questions...
|
|
(...) Yes. (...) Yes. (...) You send a code from RCX #1 to RCX #2, RCX #2 is awaiting code... Based on the code number, it can perform previously defined tasks (complex tasks too, if you like) (...) ... Don't know. More complications, I'd say. (24 years ago, 29-Jan-01, to lugnet.robotics.rcx.nqc)
|
